Water & Sanitation, Water & Sanitation Equipments, Water & Sanitation Tools, Water & Sanitation Tool Kits, Water & Sanitation Manufacturers, Water & Sanitation Suppliers from India, China, Kenya
Lab Tender Suppliers Africa and Lab Equipment Africa Kenya, Uganda, Sudan, Algeria, Morocco, Angola, Ghana, Mozambique, Madagascar, South Africa, Ivory Coast, Cameroon, Niger, Burkina Faso, Mayotte, Sao Tome, Seychelles, Zambia, Chad, Somalia, Senegal, Zimbabwe, Guinea, Rwanda, Benin, Burundi, Tunisia, South Sudan, Mali, Malawi, Nigeria, Ethiopia, Egypt, DR Congo, Tanzania, Togo, Sierra Leone, Libya, Congo, Central African Republic, Liberia, Mauritania, Eritrea, Gambia, Botswana, Namibia, Gabon, Lesotho, Guinea Bissau, Equatorial Guinea, Mauritius, Eswatini, Djibouti, Reunion, Comoros, Cape Verde, Western Sahara Ministerial Tender Board Lab Equipment India, Ministry of School Education Lab, Vocational Training Lab Tenders Suppliers India
Lab Instruments School Training Lab Equipment Suppliers India
Toothbrush suitable for children.
The bristles must not fall out with normal use.
Toothbrush of small size suitable for children, soft, and individually wrapped.
All of the toothbrush components are safe for use.
Bristles must be free of sharp or jagged edges and endpoints.
Light weight Pocket Colorimeter.
It provides Liquid Crystal Digital Display and direct concentration read-out.
Battery operated using four (4) AAA alkaline batteries.
A hand-held filter photometer factory programmed with the calibration for a single parameter (Chlorine), using the DPD method.
Range of chlorine analysis: 0-2mg/litre chlorine.
(Free and total).
Reagents are needed for the tests.
Smallest increment 0.01mg/litre.
Water sampling bag, polyethylene, sterile, self-stand-up bag type. The bag has a leak-proof closure with folding tap closing, 100ml and 4oz. Fill lines and a write-on strip.
Water Sampling bags, 100ml capacity, Sterile, Stand-up, easy and safe closing, without Thiosulphate tablets.
Compact Dry E. coli/Coliform Count (EC) is a Direct Culture based ready-to-use test method for Rapid Enumeration of Escherichia coli and coliform bacteria.
Compact Dry E. coli/Coliform Count (EC) plates for bacteriological testing of drinking water.
The medium should be rehydrated with 1mL diluted sample inoculated onto the center of the self-diffusible medium, allowing the solution to diffuse by capillary action. The plate can be incubated at 35[degrees]C for 20-24h and the colonies counted without any further working steps.
The plates are pre-sterilized, contain culture medium and a cold water-soluble gelling agent
Medium contains 2 kinds of chromogenic enzyme substrates that develop red/pink color for Coliform and white/blue color for E.coli.
Storage: Keep at room temperature (1-30 degrees C). Refrigerated storage is not required.
The kit comprises a simple sterilized plastic or glass bottle that contains dry powder medium. The powder is completely soluble in water and a dark amber colour solution is formed on the addition of water.
This is a simple bacteriological testing kit that could be used to indicate the presence of pathogens. It does not attempt to identify the pathogens.
The kit can be used with any water irrespective of its source, including chlorinated water.
The solution will change colour to black in the presence of H2S producing organisms in ambient temperatures between 25ºC and 44ºC, preferably to be kept at 35-37ºC, for an observation time of 24 to 48 hours. No incubator is needed for this range of temperatures.
The water level indicator consists of a flat, two cores, heavy duty cable calibrated in metres and centimetres on one side.
Water level depth indicator, battery powered (3 x 1.5 V, included and easily replaceable), for use in boreholes to a maximum depth of 200 metres.
A stainless-steel probe is securely fastened to the free end of the cable and the cable with probe is attached to a cable winding reel. Measurements are taken by slowly lowering the cable with probe down the borehole until the probe comes in contact with the water. On contact with the water, the unit emits a high frequency audible signal, and the user can then take a depth reading from the calibrated cable.
The unit is also equipped with an optical (light) signal that switches on upon contact of the probe with water.
The water level indicator consists of a flat, two cores, heavy duty cable calibrated in metres and centimetres on one side.
A stainless-steel probe is securely fastened to the free end of the cable and the cable with probe is attached to a cable winding reel. Measurements are taken by slowly lowering the cable with probe down the borehole until the probe comes in contact with the water.
Water level depth indicator, battery powered (3 x 1.5 V, included and easily replaceable), for use in boreholes to a maximum depth of 150 metres.
The unit is also equipped with an optical (light) signal that switches on upon contact of the probe with water. On contact with the water, the unit emits a high frequency audible signal, and the user can then take a depth reading from the calibrated cable.
Water level depth indicator, battery powered (3 x 1.5 V, included and easily replaceable), for use in boreholes to a maximum depth of 100 metres.
A stainless-steel probe is securely fastened to the free end of the cable and the cable with probe is attached to a cable winding reel. Measurements are taken by slowly lowering the cable with probe down the borehole until the probe comes in contact with the water.
The water level indicator consists of a flat, two cores, heavy duty cable calibrated in metres and centimetres on one side.
The unit is also equipped with an optical (light) signal that switches on upon contact of the probe with water. On contact with the water, the unit emits a high frequency audible signal, and the user can then take a depth reading from the calibrated cable.
Water level depth indicator, battery powered (3 x 1.5 V, included and easily replaceable), for use in boreholes to a maximum depth of 50 metres.
A stainless-steel probe is securely fastened to the free end of the cable and the cable with probe is attached to a cable winding reel.
The water level indicator consists of a flat, two cores, heavy duty cable calibrated in metres and centimetres on one side.
On contact with the water, the unit emits a high frequency audible signal, and the user can then take a depth reading from the calibrated cable. The unit is also equipped with an optical (light) signal that switches on upon contact of the probe with water.
Measurements are taken by slowly lowering the cable with probe down the borehole until the probe comes in contact with the water.
Based on the Gutzeit method, the testing kit produces a coloured strip in order to detect and visually measure soluble inorganic arsenic (As+3 and As+5).
Kit has a detection range up to 500 ppb, with the following measuring range (colour scale graduation): 0-5-10-20-30-40-50-60-80-100-150-200-250-300-400-500 ppb As+3/+5
Results are available in less than 20min, including sample preparation and necessary reaction time.
The kit includes three (3) different powdered reagents with two (2) reaction vessels, colour chart bottle label and has enough test strips and reagent to conduct 100 tests. Kit comes in a sturdy plastic case.
The displayed density measurement is correlated to a data table that corresponds directly to the concentration of arsenic in the water sample.
It allows the measure of arsenic concentrations ranging from 2 ppb to 100 ppb.
Portable, with a battery pack or used with an AC adaptor, the digital arsenic test scanner allows to simply, rapidly and accurately measure the colour density of the test strip used in the arsenic test kit.
1 x Complete set of pump body with handle retainer and HDPE top bush
1 x Complete assembly of handle assembly with rubber cushions
1 x Complete assembly bottom flange assembly with bolts, with intermediate conical flange and suitable for bolting on to concrete platform
1 x Conical rubber grommet modified
1 x Double ended spanner M17 x M19
2 x Combination spanner
1 x MS retrieving rod, 2.20 meter long, electro galvanized
1 x Solvent cement 250mt in aluminium extruded bottle
with PE stopper and sealed with plastic cap
4 x PVC pump rod with threaded joints cemented, 42mm OD x 3 meters
1 x PVC reducer (1 pc. PVC reducing socket 88.5mm ID and max. 93mm OD at the top side to fit with PVC casing pipe 89 mm OD x 60mm OD at the bottom side to fit with PVC cylinder reducer of 60mm ID & 1 pc. PVC cylinder reducer 60mm ID at the top side to fit with PVC reducing socket 60mm OD x 48mm ID at the bottom side to fit with 48 mm OD PVC lower casing)
1 x PVC top raising main with threaded joint cemented, 60mm OD x 3 meters
1 x PVC well screen assembly, 2 meters long
2 x PVC lower casing 48mm OD x 3 meters with bell connectors to fit item 15
1 x PVC sand trap complete assembly with end cap 48mm OD x 1 meter with ball connector to fit.
1 x PVC top pump rod with threaded joints cemented, 42mm OD x 3 meters
4 x PVC raising mains with threaded joints cemented, 60mm x 3 meters
1 x Complete assembly of 60mm OD x 2 meters long PVC cylinder pipe assembly with one complete foot valve assembly and one rubber seat.
Four sturdy legs (or two "A" frames), each leg fitted with a drilled plate for holding down purposes.
1 central, horizontal distribution pipe.
6 x Male threaded tap pipes welded to the central distribution pipe.
7 x Female threaded ¾" (20 mm) self-closing taps. Minimum discharge rate per tap: 10 liters per minute at one meter head, operation range: Up to 4 bars.
1 x 1 ½" (40 mm) male threaded riser pipe.
1 Female threaded 2"-1 ½" (50 mm-40 mm) junction tee with closing(for the connection to the storage tank or to other tap stands).
2 male threaded Guillemin or Storz couplings.
x ¾" (20 mm) female threaded caps (for closing in case of repair of repair of faulty taps).
4 rolls of teflon tape (12 mm x 12 meters each).
1 piece of wire netting for concrete slab, 0.9 x 1.5 meters each.(Smaller pieces could be supplied to minimize the shipping volume, provided that the necessary overlapping of the net reinforcement is taken into consideration).
4 plated pegs for fixing down of the tap stand, each 30 cm long, minimum diameter 12 mm.
Coated with PVC suitable for drinking water storage.
Water tank, 20000 litres, collapsible, made from polyester
Complete set, includes 4 water distribution kits with 2 x 6 taps, connection kit, installation kit and repair kit. Food grade material.
Riser pipe, made of AISI 304 stainless steel, CrNi 18 10.
In length of 3 metres.
Nominal diameter: 32mm.
Nominal diameter 32mm (1"1/4), both ends male threaded, one end fitted with one female threaded coupling, the other end protected with a HDPE thread protector covering the entire length of the thread.
Each riser pipe comes complete with:
One Connecting Rod
Made of Stainless Steel, with M12 rolled male thread at one end, and M12 SS female threaded coupling welded at the other end.
One rod centralizer made of nitrile rubber or similar.
Nominal diameter: 32mm.
SS Rod Diameter: 10.8mm,
Length of 3 meters (+10/-0mm).
Raised latrine kit for use in urban areas and on hard or flooded ground where impossible to dig a pit, composed of an above ground base with sludge tank, access ramp and elevated latrine slab, supporting its latrine superstructure.
....
Used for communal latrines, health centres, feeding centres, schools etc., it is composed of a double Superstructure with lockable doors, roof/cover and natural ventilation/aeration. The kit is easy to assemble to provide a stable and durable installation for a block of two (2) latrine stances/cubicles in emergencies.
Being supplied complete as a double cubicle, it has two adjacent latrine cabins per set, while the latrine slabs are supplied independently of this kit.
The kit shall be complete, ready to install, and not requiring any materials to be sourced in country for the initial installation. (However it is allowed to foresee the design for later repairs with local available materials).
The overall structures shall be of lightweight, rigid, durable and sturdy design, climatically stable and resistant to withstand heat, wind, dust, rain and manual cleaning, including stronger windy conditions.
The kit is easy to assemble to provide a stable and durable installation for one latrine stance/cubicle in emergencies. Used for family or communal latrines, health centres, feeding centres, schools etc., it is composed of a Superstructure with lockable door, roof/cover and natural ventilation/aeration.
This complete latrine cabin kit is for deployment with e.g. trench latrine installations, or with single slabs.
The overall structures shall be of lightweight, rigid, durable and sturdy design, climatically stable and resistant to withstand heat, wind, dust, rain and manual cleaning, including stronger windy conditions.
Being supplied complete as one single cubicle, it is designed to be installed either as single cabin or in groups of more adjacent latrine cabins. The latrine slabs however, are supplied independently of this kit.
The kit shall be complete, ready to install, and not requiring any materials to be sourced in country for the initial installation. (However it is allowed to foresee the design for later repairs with local available materials).
The bucket is for use at the household level to provide a safe water storage container when the lid is kept closed.
Bucket (container), stackable, round, made of HDPE (High Density PolyEthylene), with lid, cap, plastic handle and tap, water capacity: 20 litres.
Self-priming centrifugal pumping set, capacity 20 Cubic Metres per hour at around 2900 RPM, at 20 meter TMH (Total Manometric Head) for 1-m suction head.
Maximum suction lift 5 metres.
Centrifugal pump, diesel driven, with a capacity of 20 m3/hr at 20 m Total Manometric Head.
Self-priming centrifugal pumping set, capacity 30 Cubic Metres per hour at around 2900 RPM, at 20 metre TMH (Total Manometric Head) for 1-m suction head.
Maximum suction lift 5 metres.
Centrifugal pump, diesel driven, with a capacity of 30 m3/hr at 20 m Total Manometric Head.
Self-priming centrifugal pumping set, capacity 40 Cubic Metres per hour at around 2900 RPM, at 20 metre TMH (Total Manometric Head) for 1-m suction head.
....
Self-priming centrifugal pumping set, capacity 50 Cubic Metres per hour at around 2900 RPM, at 20 metre TMH (Total Manometric Head) for 1-m suction head.
....
Enriched with natural humectants and natural moisturizing ingredients.
100% biodegradable.
Hand soap for personal hygiene, suitable for all skin types even the most dry and sensitive.
Weight: 100 g.
Bucket made of HDPE (High Density Poly Ethylene), tough durable UV resistant and safe for food and water storage.
The walls should meet the bottom of the bucket with a curved inside surface to prevent dirt accumulation and facilitate cleaning.
The bucket capacity is 14 litres.
Height 33cm, top diameter 31cm.
The top is reinforced to prevent ovaling.
Water tank, collapsible, 1.5 cbm (1500 litres), made from polyester and coated with PVC, UV proof, thermal stability
Water tank, 1500 litres, collapsible, complete set including kit for water distribution with three taps, connection kit, installation kit and repair kit. Food grade material
30º/+70ºC, suitable for chlorinated drinking water storage (food grade material).
Water tank, collapsible, 5 cbm (5,000 litres), made from polyester and coated with PVC, UV proof, thermal stability -30°/+70°C, suitable for chlorinated drinking water storage (food grade material).
Water tank, 5000 liters (5 cbm), collapsible, complete set including kit for water distribution with six taps, connection kit, installation kit and repair kit. Food grade material.
Water tank, collapsible, 10 cbm (10,000 litres), made from polyester and coated with PVC, UV proof, thermal stability -30°/+70°C, suitable for chlorinated drinking water storage (food grade material).
Water tank, 10,000 litres, collapsible, suitable for drinking water storage, complete set including 2 water distribution kits with 2 x 6 taps, connection kit, installation kit and repair kit. Food grade material.
This bladder tank should be specifically designed for use on trucks for water transport.
Collapsible (flexible) water tank (bladder) manufactured from UV resistant, food grade PVC coated polyester fabric (minimum 1100 g/m2), fitted with inlet and cap on top of the tank. All materials used should be suitable for use with chlorinated drinking water.
Dimensions of the tank: 4m long, 2.2 m wide and 0.65 m high (maximum 6 tons capacity).
Chlorine, NaDCC 56%, for Water purification, as Sodium Dichloroisocyanurate (NaDCC) granules, in plastic pot of 0.5kg. Supplied with measuring spoon.
Chlorine as 100% Sodium Dichloroisocyanurate Dihydrate (NaDCC) in white granules, which releases 56% of available Chlorine:
Suitable for treatment of water for human consumption (drinking water purification).
Volume 20ml (= 15g of granules),
Supplied with measuring spoon, short handle,
Shelf life (expected): 3 years (Unopened container).
The kit is designed for a family of five; including two adults and three children/adolescents; for emergency situations for a period of one month.
Immediate Response WASH & Dignity kit sufficient for the needs of 1 Family/Household - for early response in emergencies.
The kit is designed for families of five; including two adults and three children/adolescents; for emergency situations for a period of one month.
Immediate Response WASH & Dignity kit sufficient for the needs of 5 Families/Households - for early response in emergencies.
A set of reusable, washable sanitary pads for menstrual protection to be used and reused for a duration of minimum one year.
Each set is comprised of:
2 Holders made of cotton
1 pouch for storage
3 Winged Pads
2 Straight pads
Pad material:
The holders have ribbon bands with edges well stitched by over-locking or other adequate fixation to secure the pads in position.
Pads are made of cotton, preferably flannel, for high absorbance on one side, and synthetic material on the flip side for protection against leakage.
Colors: grey or light brown.
Multipurpose Cloth.
Wrap: minimum 21 threads per cm,
Weft: minimum 18.5 threads per cm.
Color: natural, light brown or grey.
Cloth made of 100% cotton with approximate size of 1 m x 1.5 m and fabric weight of 170-180g/m2.
Collapsible water container with a capacity of 10 litres and a 50mm opening, made from food grade material. Without logo.
....
Bucket made of HDPE (High Density Poly Ethylene), UV resistant and safe for food and water storage.
The walls shall meet the bottom of the bucket with a curved surface to prevent dirt accumulation and facilitate cleaning.
The bucket has a tight-fitting lid of the same material of the bucket with an attached push-on cap.
The bucket capacity is 14 litres.
Height 33 cm, top diameter 31 cm
The top is reinforced to prevent ovaling.
Bucket designed solely for transport and storage of drinking water, made of food grade virgin HDPE (High Density PolyEthylene)/virgin LDPE (Low Density PolyEthylene), tough durable UV-resistant that will not deteriorate in harsh sunlight, and safe for food and drinking water storage.
Bucket (container), stackable, round, made of HDPE (High Density Poly Ethylene), with lid, large cap, large plastic handle and tap, capacity 14 litres.
Bucket designed solely for transport and storage of drinking water, made of food grade virgin HDPE (High Density PolyEthylene)/virgin LDPE (Low Density PolyEthylene), tough durable UV-resistant that will not deteriorate in harsh sunlight, and safe for food and drinking water storage.
....
Materials can differ, but must be plastic providing light weight, sturdy and easy to clean slab.
The upper side has a slight slope towards the drop hole of the plate to facilitate cleaning.
Self-supporting plastic direct-drop squatting plate with footrests, moulded in LLDPE with a keyhole cover moulded in HDPE.
Keyhole cover is preferably attached and hinged.
Holes are provided on the four corners of the squatting plate and can be used to secure the plate to the ground using the provided four pegs/anchors.
The underside of the squatting plate has inserts to enable the fastening of either the Pan and “Goose neck” or Pan and “P” trap options.
The squatting plate can securely support a weight of 150kg at the centre, with the two extreme ends laying off at least 100mm of firm support (ground or beams).
Pan and "Goose neck" trap set for squatting plate 120cm x 80cm.
....
The pan is moulded in PP and can be bolted to the underside of squatting plate using the fasteners provided.
The trap is fixed to the pan using the adhesive that has been provided.
There are 2 types of traps, a "P" trap and a Goose neck trap, both of which are moulded in HDPE.
Complete Vergnet hydro-pump, but supplied with 20 metres each of complete pressure (command/transmission) and riser (discharge) pipes.
....
Complete Vergnet hydro-pump; hydraulic transmission, foot operated and multi-operator pump type, supplied with 80 metres each of complete pressure (command/transmission) and riser (discharge) pipes.
....
Complete Vergnet hydro-pump, type HPV 60-2000, but supplied with 55 metres each of complete pressure (command/transmission) and riser (discharge) pipes.
Foot pump, for 55 metres installation depth.
Supplied with
1 x pump barrel
1 x command hose
1 x lower pumping element, stainless steel
1 x delivery hose
1 x base plate with sealing pins
1 x command cylinder, stainless steel
1 x pack of clips
1 x tool kit
1 x installation manual
1 x maintenance manual.
Complete hydro-pump, but supplied with 40 metres each of complete pressure (command/transmission) and riser (discharge) pipes.
Supplied with:
1 x pump barrel
1 x command hose
1 x lower pumping element, stainless steel
1 x base plate with sealing pins
1 x command cylinder, stainless steel
1 x installation manual
1 x maintenance manual
1 x delivery hose
1 x pack of clips
1 x tool kit.
Complete Vergnet hydro-pump; hydraulic transmission, foot operated and multi-operator pump type, supplied with 60 metres each of complete pressure (command/transmission) and riser (discharge) pipes.
Supplied with
1 x pump barrel
1 x lower pumping element, stainless steel
1 x delivery hose
1 x pack of clips
1 x base plate with sealing pins
1 x command cylinder, stainless steel
1 x command hose
1 x maintenance manual
1 x installation manual
1 x tool kit.
