The design of Advanced Digital Training System is easy to operate and easy to understand.
The Advanced Digital Training System is designed for the beginners to enhance the comprehension of advance digital theory.
The can serve the purposes of training students on new generation of digital autopilots, as well as familiarizing the students with the essential features of EFIS. The Two-axis digital autopilot trainer is based on an EFI Swith autopilot interface, usually found in light aircraft.
The interface to the EFIS results in autopilot operation in the following modes:
Heading Mode
GPS Navigation Mode
VOR Navigation Mode
Ground Track Mode
GPS Steering Mode
Altitude Mode
Turn-Around Mode
Localizer Tracking Mode.
The EFIS Display has the following characteristics:
Display Type: LCD, TFT (Thin Film Transistor)
Resolution: 854 x 480 color pixels.
Back light: at least 800 nits
Size: 7.0 diagonal (178 mm).
The applied force is captured on the digital display along with the revolution count of the specimen. Both values can be reset and zeroed (tared) prior to the testing commencing. When failure occurs, a microswitch stops the motor and the cycles to failure are registered on the digital display. A 2800rpm motor rotates a specimen through a gear and pulley arrangement between 5600 or 1425 rpm. The specimens are held within chucks and loaded using a cantilever arrangement, with the load being applied through a screw jack mechanism with integral cantilever load cell. This Rotating Fatigue Machine Digital Apparatus has been designed to introduce students to the effects of material fatigue using a sinusoidal variation of bending stress. The count remains when the motor is not running and the ability to reset the counter has been designed in. Through an appropriate spreadsheet software printing and manipulation of data can be completed.Specially machined necked test specimens are provided in steel. A safety guard shields all rotating parts. The digital display incorporates a usb socket, which allows a host computer to be connected to the. The software supplied with the allows the capture and reviewing of data. These have a 4mm nominal neck diameter and are held in the unit using collect chucks. All tooling is provided to allow the removal and fitting of these specimens.
Experimental Capabilities:
Introducing students to s-n curvesMaterial specification on fatigue limits
Specimen geometry on fatigue limit
To make an introductory study of fatigue using a wohler rotating fatigue apparatus, including the time to failure caused by various stress levels and materials
The accessory affords bending fatigue of a cantilevered strip of metal or plastic in modes varying from alternating to fluctuating stresses
Hydraulics Bench Chronometer Digital Flow Meter
....
Composed of of Kit For The Study Of Digital Electronics
Sub module with Flip Flop JK Master Slave
Sub module with Flip Flop D Master Slave
Sub module with 4 AND gates and 4 OR gates
Sub module with 4 EXOR gates and 6 NOT gatesv
Sub module with 4 NAND gates and 4 NOR gates
Sub module with multiplexer and Demultiplexer
Sub module with oscillators
Sub module with latch & buffer circuit
Sub module with up down counter
Sub module with 7 segment display
Sub module with shift register.
Oxygen Gas Digital Sensor
....
Pressure and vacuum mode shift function build-in 82 refrigerants according to standard refrigerants pressure and temperature relationship database.
Real-time vacuum pressure test and percent indicate
Test range Measurement of xacuum: -101Kpa~0Mpa
Positive pressure: 0Kpa~6Mpa
Low power indicate. Batteries life:30H. 9V.
Pressure units: KPa, Bar, Psi, Torr, Kg F/cm2,InHg, MmHg
Refrigerant: -101Kpa~4Kpa
Accuracy: ±0.5%
Overload: 100Bar,10Mpa
Resolution: 1Kpa
Flexural open sided frame 150 KN capacity complete with pressure transducer used in conjunction with a compression machine equipped with digital control units.
....
Spirometer Digital Sensor
....
Oxygen O2 Gas Digital Sensor
....
General Science Digital Sensor
....
AC and DC voltage output: 200mV, 2V, 20V, 200V, 500V, AC and DC current output: 2mA, 20mA, 200mA, 10A
....
It supplies the power necessary for the operation of the boards of digital electronics.
Technical Features:
1 CLK2 pulse generator, 5V amplitude, variable frequency from 1Hz to 1 kHz, rise edge synchronized with CLK1
8 logic variable (true and false) generators
3 stabilized and protected dc outputs
+12V/500mA, +5V/2A, 5.2V/500mA
1 CLK1 square wave generator, 5V amplitude, variable frequency from 1Hz to 1 kHz
9 LED for visualization of the logic states
Power supply: single phase from mains
Power Supply
Designed for electronics laboratories. Its main purpose is to realize a power supply source with high safety features and remarkable electric performance.
Output voltages of Power Supply for Digital Electronics
2 ac power supplies: 0250V/1A and 025V/2A isolated from the mains
Series of sockets: 220 V, 10/16A
2 independent stabilized supplies: 030V, 02 A, complete with digital instrument for voltage and current. Possibility of tracking.
Fixed dual supply: 24V/1A
Fixed dual supply: 5V/1A
Fixed dual supply: 12V/1Av.
This two frames Group offers the considerable advantage to perform compression tests on concrete cube, cylinder and block specimens flexural tests on concrete beams and by using suitable accessories, to perform also the following tests: Compression on portions of 40.1x40x160 mm mortar broken in flexure. Flexural high stiffness frame 200 KN capacity complete with pressure transducer, used in conjunction with a digital compression machine.
....
The board is divided in 2 sections: in the first one a discrete component realization is provided of a ramp A/D counter converter, while in the second section there is a monolithic converter. The first section is used to highlight the operating principle of an A/D converter, while the second one is mainly used to analyse the operating modes and the characteristics of the converters that are commercially available. This board allows the study of the operating principle and of the main characteristics of analogue-to-digital converters. The board is supplied complete with a set of stackable, plug-in cables of suitable lengths and colours and with a training manual.
Power supply: ± 15 Vdc, 100 mA and + 5Vdc, 200mA
The instrument foresees three memorized cycle verification program composed of ten measurement each. This user friendly menu driven digital display, connected to load cells allows to perform an accuracys verification of the loads measured from machines under control and it allows to produce the relative certificate.
At the end of the test the unit automatically elaborates the stored value and displays:
Average measured load
Accuracy in %
Effective applied load
Repeatability
Measured load.
Storage Type Digital Millisecond Table
....
Multi-purpose Digital Display Tester
....
Multi-Purpose Digital Meter
....
Includes
Fittings, hoses, universal adapter and complete set-up and operating instructions.
Requires
Test is performed automatically, allowing the user to handle other duties while the test is in process
Digital readout for more accurate testing
Large LCD touchscreen allows easy test criteria selection and data input
Air supply with a 1/4 inch MNPT fitting.
Improves the efficiency and accuracy of gas-tight garment tests for both ASTM and CE methods
Test data can be copied to the provided USB stick via the built-in USB port for record keeping.
