A sealed bottle of water inserted into a breathing circuit to add moisture to the breathing gases for administration to a patient. This type of humidifier does not heat the gas.
Graduated, transparent humidification bottle, shatter resistant.
Graduation shall show minimum and maximum water level.
Detachable metal or rigid durable polymer cap with gas connectors.
Non-heated, reusable humidifier for oxygen therapy and ventilation/anaesthesia inspiratory lines.
Bubble-through humidification system.
DISS connectors for gas inlet and outlet
All available adaptors for gas connection to be described in bid response
Flow rate capacity up to 15 L/min.
Safety pop-off valve incorporated.
Autoclavable and/or disinfectable with hospital grade detergents.
Humidification chamber working volume at least 150 ml, not greater than 500 ml.
A reusable, hand-held, manual suction device designed to suck gently and clear excessive mucus from the airway of a newborn to facilitate easier breathing.
Reusable
Material: silicone
Can be autoclaved at 136°C and withstand other means of High Level Disinfection
Fully made from transparent or translucent material
No use of natural rubber latex
Fluid capacity: 75 ml
Can be disassembled (opened up) for proper cleaning. After opening up it should be easy to access the internals of the bulb allowing for thorough cleaning.
Nozzle dimensions at tip: Inner diameter (ID) 3.0mm ±5%
Nozzle dimensions at tip: Outer diameter (OD) 4.5mm ±5%
Suction strength should reach: 100mmHg (136cm H2O).
The Rad-G sensor is only compatible with the Rad-G device.
Prior to using this sensor the user should read and understand the Operator’s Manual for the Rad-G device and the Directions for Use included with the reusable sensor.
The reusable sensors are indicated for noninvasive spot-checking of functional oxygen saturation of arterial hemoglobin (SpO2) and pulse rate (measured by an SpO2 sensor) for use with adult, pediatric, and infant patients during both no motion and motion conditions, and for patients who are well or poorly perfused in hospitals, hospital-type facilities, mobile, and home environments.
The Reusable Sensor is indicated for the continuous noninvasive monitoring of functional oxygen saturation of arterial hemoglobin (SpO2) and pulse rate (measured by an SpO2 sensor) for use with adult, pediatric, infant, and neonatal patients during both no motion and motion conditions and for patients who are well or poorly perfused in hospitals, hospital-type facilities, mobile, and home environments.
....
The reusable sensors are indicated for spot-checking or continuous, non-invasive measurement of arterial oxygen saturation (SpO2) and pulse rate for use with adult patients in operating rooms, recovery rooms, intensive care units (ICUs) and wards.
Nellcor standard compatible sensor.
Design: Reusable, finger clip
Plug type: DB9 pin
Cable length: 3.0m
Patient weight: ≥40kg.
Hard-tempered glass surface resists surface scratching
Reusable 28 × 70mm glass cuvettes
Cuvette stand stores up to 11 cuvettes or calibration standards.
Supplied with threaded light shield caps.
The reusable sensors are indicated for spot-checking or continuous, non-invasive measurement of arterial oxygen saturation (SpO2) and pulse rate for use with children in operating rooms, recovery rooms, intensive care units (ICUs) and wards.
Nellcor standard compatible sensor.
Design: Reusable, finger clip
Plug type: DB9 pin
Cable length: 3.0m
Patient weight: 10 - 40kg.
The reusable sensors are indicated for spot-checking or continuous, non-invasive measurement of arterial oxygen saturation (SpO2) and pulse rate for use with neonates in operating rooms, recovery rooms, intensive care units (ICUs) and wards.
Design: Reusable, Y-style with built-in wrap-around belt for use on big toe or thumb.
Nellcor standard compatible sensor.
Cable length: 3.0m
Plug type: DB9 pin
Patient weight: 3 - 20kg.
Quick-release snap front closure
Two front pockets and one left breast pocket
Side seam openings for pants pocket access
These specialized lab coats offer excellent fluid resistance while maintaining their breathability.
Splash Resistant Polyester front and sleeves
Breathable Poly Cotton back panel for ventilation
100% polyester fluid-resistant front and sleeves
Industrial launderable
Can be used as part of an Compliance Plan.
These specialized lab coats offer excellent fluid resistance while maintaining their breathability.
100% polyester fluid-resistant front and sleeves
Quick-release snap front closure
Breathable Poly Cotton back panel for ventilation
Splash Resistant Polyester front and sleeves
Industrial launderable
Two front pockets and one left breast pocket
Side seam openings for pants pocket access.
CleanroomCoverall-lab-2081475228.jpg "PIP Uniform Technology Reusable (Class 10) Cleanroom Coverall")
Coverall that Groundable Static Control Garment.
Coil zipper
Snaps at top of zipper
Raglan sleeves for more movement
Knit cuff
Color coded hang loop
Snaps at leg hem.
Reusable frocks with coil zipper enclosure are suitable for a variety of cleanroom applications including pharmaceutical, biotechnology, and medical device manufacturing.
Wide-pull zipper with a single snap at bottom
Cuff Sleeves
Fluid and bacteria resistant Integrity high performance carbon striped fabric
Mandarin collar with two snaps at top
Silicon-free
Laser-cut, pre-serged seams
ESD carbon stripes provide electrostatic dissipation.
