This category basically includes: buses, Lorries of various dimensions, special Lorries, haulers. The simulator analyzes also the starting systems with the device for starting repetition, those with the relay for double starting for operation in parallel and those with the switching relay for the operation in parallel. This simulator mainly takes into consideration the 12V and the 24V starting systems with switching of the batteries and the starting systems with the device for starting block. According to the great variety of industrial vehicles also the starting systems are always adapted to the structure and type of motor of the vehicle on which they must be put.
The term "industrial vehicle" is normally used for the vehicles which are made for the transport of more than 9 people, for the transport of goods and or for the haulage of trailers.
The axial force (feed force) and torque occurring during cutting are measured using strain gauge transducers and digitally displayed on the amplifier unit. Investigation of cutting forces during drilling is fundamental to the teaching of cutting techniques. The set-up comprises a transducer, which also holds the specimen being machined, and an amplifier unit with digital displays. The well-structured instructional material sets out the fundamentals and provides a step-by-step guide through the experiments. The experiments must be conducted in a workshop environment, as a suitable drilling machine is required.
....
Self contained floor standing unit with integral control and instrumentation console
Probes at each stage allow full monitoring of the process With the data logger, the product concentrations can be directly displayed in real time (for the recommended material)
Three stage extraction process, can also be configured as one or two stages
Independent vessel for closed loop batch extraction
Temperature control at each stage
Individual control of solvent feed pumps at each stage, of cell rotation rate and of feed rate
Optional data logging accessory with USB interface and educational software.
Anodized aluminum structure and panels in painted steel.
Diagram in the front panel with similar distribution to the elements in the real unit
Main metallic elements in stainless steel.
Unit to perform experiments with a SCADA SOFTWARE.
System control via solenoid valves.
The unit includes wheels to facilitate its mobility.
Base unit of the unit that allows the development basic experiments on the operation of the refrigeration and air conditioning systems in conjunction with different models.
Function educational.
Models attached securely with fasteners.
Condenser unit with: Compressor, Condenser, Receiver of refrigerant.
Data acquisition.
Automation of the air operation system.
The Centrifugal Pump With Stuffing Box Learning System includes a cast iron-housed centrifugal pump with stuffing box and a piping network that features a pressure line, suction line, and pressure gauge hose. The Centrifugal Pump With Stuffing Box Learning System explains the installation, function, and maintenance of a centrifugal pump with a stuffing box. The Centrifugal Pump With Stuffing Box Learning System covers a pump design that, in spite of the modern mechanical seal, remains widely used in industry due to its cost-effectiveness and ability to avoid catastrophic failure. Additional topics include: how to troubleshoot this pump design; what the flow/pressure characteristics of a centrifugal pump are; and how to startup and operate a centrifugal pump with a stuffing box. This feature makes it an ideal design for fire departments in fire pump applications. This commitment to providing learners with the most realistic and applicable training available is one example of how is transforming the global workforce one life at a time. These components allow learners to practice skills on an industrial-grade centrifugal pump that they may work with at real-world job sites.
Features:
Industrial Quality Centrifugal Pump
Stuffing Box Packing Type Seal
Mounting Compatible with Workstation.
A system of solenoid and manual valves enables the desired configuration to be chosen, to simulate the most commonplace faults and to section the circuit during maintenance operations. The Modular Trainer On Refrigerator System enables the study of refrigerator systems based on different types of compressor (hermetic, semi-hermetic, open) and expansion systems (thermostatic valve, thermo-pressure valve, capillary tube). The system uses CFC-free refrigerant fluid Freon R134a (HFC) and includes measuring instruments to monitor operating parameters and test the refrigerator circuit. Modular Trainer On Refrigerator System uses air condensers (one for each compressor) and an air evaporator and includes a defrosting system based on electric resistances operated by a timer.
....
Demonstrations:
Function of the locking mechanism in the case of wheel spin
Function of the thrust rings and friction disks
Function of the axle drive (bevel gear - differential ringgear)
Function of the differential when cornering.
Features:
Suitable for HCFC and HFC refrigerants and blends
Spare parts for 1 year including 5 replaceable filters
Overpressure protection system
3/4 HP compressor
Compact and easy to carry
OFP feature
Replaceable filter
Size: 465*225*360mm
Slump Cone Plastic complete set including:
Tamping rod, galvanized steel dia. 16 x 600 mm
Base plate, galvanized steel
Slump Cone, plastic Weight: 750 g
Aluminium scoop, 500 cc capacity
Stainless steel rule, 300 mm long
Fine wire brush
Max. Cutting Dia. For Vertical Tool Post: 1000mm 1250mm 1600mm 2000 mm
Max. Cutting Dia. For sideway tool past: 1000mm 1100 mm 1400mm 1800mm
Table dia.: 900mm 1000mm 1400mm 1800mm
Max. Work height: 800mm 1000mm 1000mm 1250mm
Max. work load: 2000 Kg. 3200Kg. 5000Kg. 8000Kg.
Table speed range: 16/8-250rpm 16/6.3-200rpm 16/5-160rpm 16/4-125rpm
Feed range for both tool past: 0.9-103 0.8-86 0.8-86 0.8-86
Horizontal travel for vertical tool past: 670mm 700mm 900mm 1110mm
Vertical travel for vertical tool past: 650mm 650mm 800mm 800mm
Horizontal travel for sideway tool past: 500mm 500mm 650mm 630mm
Vertical travel for vertical tool past: 810mm 900mm 900mm 1110mm
Ram travel: 580mm 650mm 650mm 650mm
Main motor power: 22kW 22kW 22kW 30kW
Machine Weight: 7100Kg. 8500Kg. 13000 Kg. 17500Kg.
Capacitive Load Bank
....
Safety devices show how the drinking water pipework is protected against the backflow of waste water. A typical household drinking water installation is fitted to the panel. A small electrical boiler for hot water and a circulation pipe with the related components demonstrate the heating of domestic hot water from the cold water supplied.
Learning objectives/experiments:
Reversible flow filter
Backflow preventer / system separator
Function and operation of components
Water meter
Circulating pump
Thermal discharge safety device
Pressure reducing valve with and without
Pressure vessel with heater
System of safety devices.
Pressure Control And Regulation Study Unit makes it possible to analyse the behavior of a control loop where the controlled quantity is the pressure of the air ina tank. Pressure control is one of the main problems encountered in factory automation and process control. Students can examine the effects of the different control parameters on the performance of the control chain and on the stability of the system; furthermore, they can become familiar with the components commonly adopted in modern industrial applications, as the system is entirely made of industrial quality components. With this trainer, all the tests can be performed through a Personal Computer and a special software for Windows. This makes the problem of choosing the most suitable control technique very interesting. Compared to other quantities such as the level or the temperature the pressure varies as a function of the regulating signal in a very quick way.
....
Water circuit with tank, heater, temperature controller, pump and low water cut-off for heating and cooling (with wl 110.20 water chiller)
Supply unit for 6 different chemical reactor types
Connection of the reactors via hoses with quick-release couplings
Temperature control of the reactants and reactors
5 peristaltic pumps to deliver the reactants and products
2 combined sensors for measuring the conductivity and temperature
3 glass tanks for reactants and products.
Features:
Incorporates widely used industrial PID controller.
Temperature/time profile set-point ramp facility
Fuzzy and adaptive tuning
PID with alarm and relay outputs
Configuration in engineering units
Serial communications RS232 and RS485
Alternative control algorithm
Dual set-points
Introduction to SCADA, (supervision of the controller by a PC) using Windows based serial communication software.
Pressure measurement: Electronic transducers and digital display
Power, speed and torque measurement:
From Universal Dynamometer
Nett dimensions and weight (assembled):
2300 mm x 1060 mm x 1530 mm and 200 kg
Packed volume and weight:2.4 m3 and approximately 300 kg
Nominal Fan Diameter: 400 mm
Flow rate: 1.7 m3.s1
Experiments:
Introduction to limit state design
Relationship between maximum loading and plastic hinge formation for a simply supported beam, a propped cantilever and a fixed beam
Relationship between load and deflection for beams loaded to the plastic condition
Introduction to form factor.
The Cam Analysis consists of 3 interchangeable cams and 2 different cam followers. The cams are rotated using a electronically controlled motor and pulley gear arrangement. A large inertia mass is connected between the motor and cam to ensure consistent running at various speeds. Bench top apparatus to demonstrate the dynamic investigation of cam mechanisms, as used in motors for actuation of the valves.
On top of the shaft can be attached a number of removable masses which allow the valve mass to be changed. The follower attaches to a vertically moving shaft which simulates the valve itself.
Experimental Capabilities:
Determination of the limiting speed and its comparison with the theoretical value
Comparison of the various cam designs
Elevation curve for a bouncing pick-up
Relationship between cam and spring force
Elevation curves supplied by unsuitable pick-ups.
The is designed to connect to the to expand the experimental capability.
The has been designed and manufactured to incorporate all current safety standards.
A Computer Controlled Thermodynamic Cycle of a Screw Compressor training plant for studying the energy transfer in a compressed air system.
It includes industrial sensors and transducers.
The is controlled by a PC and software.
Experiments:
Determining the polytropic index
Calculating the effective average pressure of the compressor
Analysing the pressure / volume diagram of the first and second stages of the compressor by experiment
Checking the operation of the safety devices:
For detailed study of the air characteristics it is necessary to connect the ACV85 to the ACV90 Compressed Air Dehumidification Training Plant
Using a T-s diagram for air to determine the characteristics of the thermal cycles by experiment.
Accurate torque meter systems. The new Torque Sensor uses the latest technology, without need for regular calibration.
A handy physical size.
Possibility to use standard instruments.
A comprehensive range of test machines with accessories, to show typical characteristics, valid also for larger machines.
