The Level Process Training System is a compact and mobile unit for a wide range of experiments in flow control. It gives students a greater understanding of the stability of simple control systems. The self-contained unit can do many experiments, but it can also connect to other products in the range for extra experiments. For cascade control of flow and level, it can link to the optional Flow Process Training System. For distributed control, it can connect to the optional Computer Control System
....
The bending beam can be used vertically standing or hanging and in the horizontal position in the mounting frame. An oscillator, which is left alone after a single excitation, performs free vibrations. In this, a bending beam is used as the systems oscillator. The frequency of the free vibration is the natural frequency of the oscillator.
Learning Objectives And Experiments:
Determine the natural frequency according to Rayleigh
Free vibration in a vertical and horizontal bending beam
How clamping length and mass affect the natural frequency.
Features:
Approximation method according to Rayleigh.
Natural frequency on the freely vibrating bending beam.
Commercial Refrigeration Training Unit the powder coated evaporator is a forced air, blow through type with removable front panel and galvanised sheet steel casing. Commercial Refrigeration Training Unit consists of an air cooled condensing unit with high back pressure, high starting torque hermetic compressor, Complete with: Suction and Discharge Service Valves; Gauge Manifold Connections and Built in Motor Protector. The evaporator is a finned coil type with fins a 5 fins per inch.
Commercial Refrigeration Training Unit unit may be thermally loaded for performance investigation and has a dial thermometer; Liquid Line Filter Drier; Liquid-vapour Heat Exchanger; High Pressure Switch; Low Pressure Switch; Internally equalised Thermostatic Expansion Valve; High Pressure gauge; Low pressure Compound gauge.
This trainer includes a clear horizontal primary separator vessel. The process has manual control valves with rotameters and is intended to demonstrate oilfield separation principles with basic visual manual operation. The three phase separator demonstration apparatus is a small scale vessel that performs continuous separation of a mixture of oil, air and water. The primary separation operation for crude oil occurs when the crude stream flows through a vessel of sufficient capacity to allow gravity separation of the gas, liquid hydrocarbon and water phases. It is available in horizontal and vertical orientations.
Function:
This fluid mixture then flows into a separator vessel fabricated of clear materials. The oil and water are recycled the air is vented to atmosphere. This process trainer blends air, water and refined oil to emulate a crude oil stream.
CNC Machine Operators require skills in operating a CNC machine but are not machinists. Many training programs for CNC Machine Operators use training really designed for machinists, which incorporates a lot of theory not relevant to the role of CNC Machine Operator. For example, a CNC Machine Operator needs to know how to run a CNC program not how to design one. Through industry task analysis as well as strong involvement with our development partner, a large global manufacturer, CNC Machine Operator Program brings a highly focused, streamlined set of skills to CNC Machine Operator training. NIMS provides national standards for metalworking. NIMS (National Institute for Metalworking Skills) endorses CNC Machine Operator Program -FANUC Based Interface exclusively as the recommended preparation method for the NIMS CNC Machine Operator Certification.
Features:
24 Self-paced Learning Units
132 Skills, 80+ Hours of Learning
Highly Interactive Exercises
Nationally Recognized Certification
Strong STEM Development
OTJ (On-The-Job Training) Guide
Instructor's Guide with Authentic Skill Assessments.
The Wiring Harness Assembly Learning System includes a welded steel, mobile workstation with 4 square welded steel tubing and heavy duty casters. Supplies these industrial-grade, top-flight components in order to give the learner an opportunity to work with real-world materials and gain experience they would normally only acquire on the job. Components include a wire harness kit, fastener kit, cable kit, and harness assembly tool set, which features four wrenches, three pliers, and a tie-strap tool.
Wiring Harness Assembly Learning System introduces learners to the basic concepts of wire harnessing, such as wire routing, common types of connectors and clips, harness installation, and troubleshooting. World-class interactive curriculum allows learners to grasp both technical knowledge such as common wire routing mistakes and hands-on skills like practicing battery cable installation. Because machines require thousands of individual wires, harnessing offers protection for the wires, as well as ease of routing, reduction of space, and standardization of the assembly process for machine operators and assemblers.
Features:
Wire Harnessing Safety
Multimedia Curriculum Available
Real-World Wire Harnessing Knowledge
Hands on Wire Harnessing Skills
Student Reference Guide.
The propeller dynamometers are new designs to replace earlier dynamometers only adjustments to the inclination of the propeller shaft could be made, but with the introduction of the adjustment of propeller shaft height can also be achieved. Depending on the maximum capacity of the drive motors, the maximum torque ratings, and consequently the diameters of the propeller shaft ends, are different. The capacity of the drive motors of the same whereas that of less. Apart from the different arrangement possibilities,the technical details of all essential parts of propeller dynamometers are identical, with exception of the capacity of the drive motors and the maximum load ratings in respect of measurement of torque and thrust.
....
It consists of body housing, a geared screw jack and motor drive mechanism suitable for operation on 230 V, 50Hz, Single Phase, A.C. supply.
Marshall Apparatus Consists Of:
50KN capacity
Robust construction
Safety cut-off switch
Rate of travel 50.8mm/min
-lab-374703529.jpg "Torsion Testing Machine (100Nm)")
The Torsion Testing Machine exhibited to the test specimen is measured using strain gauge technology. The output from the strain gauges is fed directly into the Data Acquisition Interface supplied, which reads torsion directly in Nm. The input angle of twist is recorded on an integral protractor and a rotary potentiometer that connects to the Data Acquisition Interface supplied. Test specimens of up to 350mm can be loaded between the torsion head and fixing head using standard hexagon drives. Torsion Testing Machine for manually applying torque to test specimens until failure occurs. Torque is applied to differing material test specimens using hand operated gearbox. The fixing head slides along the base.
Experimental capabilities:
Torsional loading to failure of varying material specimens
Determination of the Modulus of Rigidity and Yield shear stress
Working with the elastic torsion equation
Comparison between actual and theoretical results
Torsional variation due to material, cross sectional area.
1a Plane Frame With Strain Gauges is made from fully welded hollow square section steel members making a 45° truss. The end mountings also allow the frame to be inverted for work on an inverted truss. Seven members of the truss are 1a Plane Frame With Strain Gauges With half bridge arrangements. The truss has special end mountings supplied that allow different end bearing conditions to be used, i.e. pinned and roller end.
The truss has been specially designed to be tested in the MAGNUS Test frame. The standard accessories supplied with the are required. Each 1a Plane Frame With Strain Gauges pairing has a cable loom attached and terminated with a numbered connector. The experiment calls for joint deflections to be measured during testing. Safety chains and high level reaction supports are supplied with this apparatus. This connector can be fitted into the optionally available Data Acquisition Interface for direct reading of the member strain during loading.
Experimental Capabilities:
Measurement of strains in members of a fully welded truss
Investigation of reciprocal theorem
Strain gauging of welded structures
Comparison of deflections with theoretical values assuming pin joints
Investigation of reciprocal theorem
Strain gauging of welded structures
Comparison between normal and inverted trusses
The use of strain gauges and strain meters
Measurement of strains in members of a fully welded truss
Comparison of deflections with theoretical values assuming pin joints
Comparison between normal and inverted trusses
The use of strain gauges and strain meters
Rectangular mosquito net, polyethylene 120-150 DENIER, treated with WHO PQ qualified insecticide, colour white/blue/green, dimensions 190 x 180 x 150 cm (length x width x height) +/-5%.
....
Intended use:
Various general clinical laboratory usage conditions including sample preparation, separation, centrifugation, and cold storage.
Rotator mixer for blood samples to ensure a homogenous mixture for clinical laboratory applications.
....
Vaccine storage capacity: 225 L
Volume category: >120L
Refrigerant: R600a, 68 grams
Energy consumption, stable running (kWh/24 hours): 2.04
Prequalified Intermittent Mains Powered Refrigerator for storage of vaccines at +2 ?C to+8?C.
Operating temperature: Min and Max rated ambient temperature:+10 C and +43°C
UIFPF- Grade A
Equipment operating voltage and frequency: 220-240 Volt, 50Hz/60Hz or 100-127 Volt 50Hz/60Hz, 1ph.
Vaccine storage capacity: 102 L
Volume category: >/= 60, <120L
Operating temperature: Min and Max rated ambient temperature: +5 °C and +43°C
UIFPF: Grade A
Solar radiation reference period of 3.5 kWh/m²/day and hot zone (+43°C) test temperatures.
Refrigerant: R600a, 100 grams
PQS prequalified Solar direct drive combined refrigerator and freezer with no battery for storage of vaccines at +2?C to+8?C and freezing of ice packs in areas without any electricity, or where there is less than eight hours of reliable electricity over a typical day.
Remote Temperature Monitoring (RTM) system for real time monitoring of storage conditions at different levels of the vaccine cold chain: (a) capable of alarm notifications via SMS, email and/or iOS & Android mobile applications (b) with integrated audio-visual alarm (c) with data access, setup of alarm thresholds and setup of alarm recipients through internet accessible dashboard (d) with automatic transmission of data to a server (e) configurable to suit specific applications and scalable to allow for the later installation of additional temperature monitoring products and/or storage facilities.
....
Capacity: 100L
Cabinet Type: Upright
Volume Category: ≥ 80 <300L
Power requirement: 220-240V/50Hz
Operating ambient temperature: +10 °C - +32°C (Temperate zone).
Storage temperature: up to-86°C
Adjustable cabinet temperature set point -40oC to -86oC
Suitable for preliminary emergency response set-up or small size field office installations. It is not recommended as a permanent solution or for large and heavy antennas. Complete portable antenna mast supporting light-weight HF and VHF antennas for temporary installations.
....
A1 Manila paper, assorted colors, 80 sheets, SRA1
Size - 900 x 640mm
Material: Cotton/polyester blends.
The edges of the insignia overlock-stitched or heat cut, to avoid fraying.
Color: Cyan blue, with a woven horizontal logo in white, centered vertically.
Insignia, cotton/polyester blend, rectangular, 85x41mm.
