Features:
Assists in the Study and Diagnosis of most Automobile Systems.
The Automotive Technology Trainer or car clip is a late model recycled front-wheel-drive vehicle.
Including:
a. Engine Performance
b. Heating/Air Conditioning
c. Suspension/Steering
d. Electrical/Electronic
e. Brake
f. Transmission
Performs Actual Service Manual Diagnostic Procedures
Aids in Developing Real-World System Skills and Knowledge
Includes a Fault/Simulator Panel with Multiple Faulting Options and Features Including:
a. Real-Time voltage readouts for Various Selectable Sensors
b. Investigates Downstream Oxygen Sensors Control of Fuel Trim
c. Voltage Adjustment Potentiometers for each Sensor
d. Individual or Multiple Sensors are selectable for Voltage Substitution
e. Demonstrates Catalytic Convertor Punch-Through
f. Interactive Demonstration/Study of Fuel Control by Oxygen Sensor Feedback.
Terminal block receptacles are provided for diagnostic test points. The Two-door Power Window System Trainer allows for the demonstration of a complete power window system using real-world components.
Educational Advantages:
Ability to test and verify a basic 2-door power window circuit.
Four operational faults can be inserted to promote student diagnostic troubleshooting competencies.
Includes wiring schematics.
Ability to visualize the operation of power window actuators and switches.
Main Components:
Application: 2007+ GM Chevrolet Cobalt
Fault box with 4 faults.
Test points for diagnosis.
Power window motors (2ea).
Master and slave switches.
Dimensions: 22 x 22 x 8 in (55.9 x 55.9 x 20.3 cm)
Weight: 13 lb (5.91 kg).
Maximum load: 500G;
Division value: 20 mg.
Lightweight polyester solid material on front, mesh material on back
Black Reflective Safety Vest features include high visibility markings on the front and back, pockets, and a zipper front closure.
Clear front pocket
8 pockets: 5 outside, 3 inside
2 in. silver reflective material with 4 in. contrasting color trim
Badge/Microphone tabs located 3 in. below each shoulder seam.
Investigating the stability of a floating body and determining the metacentre
One vertically movable clamped weight for adjusting the centre of gravity
One horizontally movable clamped weight for adjusting the heel
Clinometer with scale for displaying the heel
Transparent floating body with rectangular frame cross-section.
The trainer is capable of duplicating actual on-vehicle problems. The program provides courseware for use by students and instructors. The Trailer Air Brake Trainer presents the real world operation and study of a Trailer Air Brake System.
Features:
Air Gauge
Drain Valve - Manual
W-Way Check Valve
Spring Brake
Service Brake Chamber
Brake Light
Tractor Hook Up
D.O.T. Air Brake Lines
Service and Emergency Glad Hands.
The Power Door Lock System Trainer Two Door Hyundai is a functional Power Door Lock System Trainer mounted on a plastic training board with the following features:
A lockable system fault box allowing instructors to insert from one to four faults for student diagnostic learning.
Electrical test points are included on the trainer for circuit diagnosis.
User manual included.
Trainer requires an external 12VDC power supply to operate.
OEM components (door lock actuators, switches, with OEM matching wire colors).
Students can wire this circuit using supplied leads and included OEM wiring diagrams.
Advantages:
Power door lock actuators (2ea).
Test points for diagnosis.
Door lock relay.
Set of 21 jumper leeds, 24 (60cm) (6 red, 1 black, 14 blue).
Fault box with 4 faults.
The product for foot, hand press type dual-purpose, by suction nozzle, a cylinder cover, piston rod, a piston, a cylinder, a sealing ring, a bracket, an air inflating valve, outlet valve plate, pressure plate, a spring, a base and other components. The limit of the suction pressure is less than 6.7 * 103Pa (500mmHg), the minimum air pressure is over 2.9 * 105Pa (3kgf/cm2). Products by the outer cylinder and the suction nozzle, an air inflating valve, a base made of ABS engineering plastic pressing as a whole, the outer cylinder size diameter 36mm x 130mm, bottom diameter is 80mm.
....
For men and women
Three patch-style pockets on outside, plus one inside pocket
Button-front closure
Two-piece swing belt
Made of 65% polyester, 35% cotton poplin
Length: 40 in. (102cm)
Washable
Not fluid resistant or antimicrobial. 4 pockets. Slits provide access to pants pockets.
Embroidery available upon request.
Tall and sizes up to 4X available upon request.
Comprehensive experimental introduction to hydrostatics
1 experimental unit each: measuring the buoyancy force, investigation of the hydrostatic pressure in Liquids, measuring the surface tension, communicating vessels, capillarity
Wide range of accessories included: compressor for generating negative pressures, bottom pressure apparatus, two areometers
Transparent tank for observing the processes.
The Diesel Engine Performance Trainer has a new or used diesel engine and components, depending upon customer request. The trainer includes fuel, air handling control, cooling, and exhaust after treatment systems. The Diesel Engine Performance Trainer presents the live operation and study of a fully functional diesel engine.
....
The trainer contains an alternator, a driving motor with AC drive, a drive belt, a battery terminal block, an internal voltage regulator and the associated wiring. The Alternator Trainer With Internal Voltage Regulation is in fact a simulator that allows instructors to demonstrate the operation of automotive charging systems with an internal voltage regulator. The charging system is a circuit with the battery wired in parallel. After the engine is started and running, the alternator takes over as the source of power and the battery then becomes part of the load on the charging system. The synoptic diagram and the layout of all the control and instrumentation units provide clear and simple operation to the user. The trainers are very reliable and equipped with all safety equipment required for demonstration.
Educational Advantages:
Ideal for demonstrating internal voltage regulation
Test points for diagnosis
Optional built-in diagnostic fault box with 4 faults
Main Features:
Built-in voltmeter and ammeter
Protective cover
Driven by 120VAC electric motor.
1. High-frequency signal frequency range: 400KHz -130MHz; (have 5 range)
2. Low-frequency signal: frequency 1KHz ± 5%, the rate of not less than 20mV continuously adjustable; power supply: AC 220V ± 10% 50Hz ± 5%.
Made with Sandwash material, this lightweight micro-denier fabric is woven from 100% continuous-filament polyester to eliminate any source for lint.
Widely used in pharmaceutical cleanroom operations
Pullover design with three-snap
ESD long sleeve scrub tops are made from non-linting, breathable fabric and are ideal base-layers in controlled environments.
Sleeves include color-coordinated filament knit cuff for extra comfort
5 in. side slits at garment bottom for added comfort and long-term durability
Henley-style collar that provides added room for easy on/off
Binding on collar helps maintain shape and uniformity
Raglan-style sleeves provide increased mobility
These scrubs provide an excellent base-layer of protection for any cleanroom garment system.
Experimental investigation of gas laws
Hydraulic oil filling for changing volume of test gas
Built-in compressor generates necessary pressure differences to move the oil volume
Transparent measuring tank 1 for investigation of isothermic change of state
Transparent measuring tank 2 for investigation of isochoric change of state
Electrical heater with temperature control in tank 2
Sensors and digital displays for temperatures, pressures and volumes
Compressor can also be used as vacuum pump
5/2-way valve for switching between compression and expansion.
Aids in Developing Real-World System Skills and Knowledge
Test Points for the Following Signals:
a. Battery (12V)
b. Electronic Spark Timing (EST)
c. 6X Reference
d. Reference
e. Bypass
f. Ground
The Direct Ignition System (DIS) Trainer Demonstrates the Operation of an Actual GM Waste Spark Ignition System
Uses Actual Automotive Components Including:
a. Spark Plugs and Spark Plug Wires
b. Magnetic Generator Type Crankshaft Position Sensor
c. Two Dual Tower (Waste Spark) Coils
d. Ignition Control Module
Fault Codes, used for Diagnostics, can be Inserted Either Locally through the Keypad, or Remotely via a Instructors PC
Spring-Loaded Lever to Vary CKP Gap
Internal 12V Power Supply
Speed Variable From 0 - 3,000 RPM
Courseware is Included (Student Manual, Instructor Guide, Service Manual Information).
The Power Window System Trainer Four Door Hyundai mounted on a plastic training board with the following features :
Electrical test points are included on the trainer for circuit diagnosis.
Trainer requires an external 12VDC power supply to operate.
Students can wire this circuit using supplied leads and included OEM wiring diagrams.
OEM components (window motors, switches, with OEM matching wire colors.
A lockable system fault box allowing instructors to insert from one to four faults for student diagnostic learning.
User manual included.
Educational Advantages:
Fault box with 4 faults.
Test points for diagnosis.
Power window motors.
Master and slave switches.
Set of 21 jumper leeds, 24 (60cm) (6 red, 1 black, 14 blue).
Power supply voltage: 220V ± 10%, 50Hz; Audio output power: 0.5W; output signal amplitude 0-4V; Tempo: 10-290 times / min.
....
Strong polypropylene and polyethylene material
Anti-skid
Waterproof
Fluid resistant and wear resistant
Shoe covers are made with a multi-layer fabric to provide water resistance and anti-skid properties and are ideal for labs and cleanroom environments.
Durable protection
Low linting, suitable for cleanrooms up to level ISO 5
Disposable
Available in Universal and XL sizes
Seamless sole and sides.
Basic principles of open-channel flow
Experimental section with 10 evenly spaced threaded holes on the bottom for installing models or for Water level measurement using pressure
Side walls of the experimental section are made of tempered glass for excellent observation of the experiments
Experimental flume with experimental section, inlet and outlet element and closed water circuit
All surfaces in contact with water are made of corrosion-resistant materials
Flow-optimised inlet element for low-turbulence entry into the experimental section
Length of the experimental section 2,5m or 5m
Smoothly adjustable inclination of the experimental section
Models from all fields of hydraulic engineering available as accessories
Closed water circuit with water tank, pump, flow rate sensor and manual flow adjustment.
