The trainer is composed of:
A control module, containing the interface circuits for the sensors and the actuators and the ON/OFF, proportional, integral and derivative control circuits (PID).
An educational board with a pressurized vessel and a set of sensors and actuators for level, pressure, temperature and flow;
Technical Features:
Water tank capacity: 20 litres approx.
Pressurized vessel capacity: 5 litres approx.
Level sensors:
On reed ON/OFF sensor
Linear variable differential transformer (LVDT)
Temperature sensors:
Bi metallic direct reading thermometer
Platinum thermo resistance
Flux sensors:
Flowmeter, direct reading
Flowmeter 8000 pulses/ litre
Pressure sensors:
Manometer, direct reading
Strain gauge.
Flow setting by manual stroke length adjustment (including during operation)
Manual drive with crank instead of a drive motor
Learning concept for maintenance and repair exercises on a single-diaphragm pump
The kit forms part of the GUNT assembly, maintenance and repair practice line
Diaphragm and push rod directly linked
Pump parts and tools housed in a tool box.
For use with Statics Fundamentals range, the Work Panel fits on most desk or bench tops. Fundamentals kits to the Work Panel to study or demonstrate one of the fundamental topics of static forces. Students or teachers fit the magnetic parts of their Statics.
Available Experiment Modules
Equilibrium Of Forces
Equilibrium Of A Beam
Suspension Cable Demonstration
Equilibrium Of A Rigid Body
Various general clinical laboratory usage conditions including; sample preparation, separation, centrifugation, cold storage.
....
Oro-pharyngeal airway, Guedel type.
Material: Polyethylene/vinyl acetate (EVA) - Polyvinyl chloride (PVC).
Sterile, single patient use.
Semi-rigid, transparent.
Proximal (or buccal) end straight and reinforced.
Flange colour coded and/or marked with corresponding size number.
Initial sterilisation method:
Ethylene oxide gas or gamma radiation.
Size: Airway Guedel, size 3, Length approximately 80mm.
The pressure spring is made from 1.5mm diameter carbon spring steel wire with flat ends. Length: 70mm, diameter: 20mm.
....
Clear turbidity standards are recognized by the EPA as a primary standard for the calibration of turbitidy meters online and in the laboratory for drinking water analysis.
Clear turbidity standards are traceable to NIST Primary Standards on account of their consistent particle size and photometric accuracy via UV-VIS spectroscopy.
Each lot is normalized to historical lots which were formulated to dilutions of 4000 NTU Formazin.
Face Shields are lightweight and comfortable. They provide protection from splashing liquids, blood, and other bodily fluids and are ideal for use in laboratories, medical settings, dentistry, and veterinary medicine
High-quality, optically clear disposable face shield
Anti-fog and non-glare design
Flexible construction with comfortable polyurethane foam headband
Medical face shield
Optical grade PET construction
Secures to head with elastic band
Class 2 Medical Device, 510(k)
Latex free.
Magnetic Field Sensor
....
Automatic Gas cutting M/C
....
Screw-locking devices are presented in the as-fitted position on an aluminium panel. A transparent multi-compartment storage tray holds large numbers of screw-locking devices. This instructional kit is used for demonstration and information purposes. The well-structured instructional material enhances the informational value of the kit. No provision is made for conducting exercises or experiments. The kit is clearly laid out on a plastic tray.
....
The unit consists of a storage tank and a centrifugal pump with multi speed motor on a steel base, and measuring instruments. Compact Centrifugal Pump Test Set Multi SpeedCompact Centrifugal Pump Test Set Multi Speed is a self contained bench top unit for studying the centrifugal pump flow rate vs head at three different speeds.
Experiments:
Flow rate vs head at three different speeds.
The Computerized Concentric Pipes Heat Exchanger Study Unit has been realized to study the operation of a heat exchanger, concentric pipes type. The water is heated by a proper electric resistance. A set of valves enables to operate either in equi-current or in counter-current conditions. The unit is provided with a wheel-mounted frame and includes all the measuring instruments necessary to perform the experiments. A three-speed motor-driven-pump generates the hot water flow in the primary circuit while in the secondary circuit the water is directly drawn by the water mains. This type of exchanger, which is very common in the industrial field, enables the student, owing to its simple construction, to quickly learn the thermal exchange concept and study the main parameters by varying the operation conditions. The system is supplied with manuals which describe all parts of the trainer, the installation and utilisation procedures, as well as many exercises with the relative results. A data acquisition and analysis system for personal computer allows to take the measurements automatically, to plot the curves on screen or print them out, to store the experimental data on disk or print them.
....
A tube is attached to a measuring frame that allows the device to be traversed horizontally and axially over the whole flow field. By this method the velocity profile at various axial distances from the jet, the pressure loss and entrained mass may be investigated.
A round parallel tube with a sharp edged discharge is used to create a turbulent jet using the air from the Air flow System.
This allows incorrect wear patterns and excessive tooth backlash to be demonstrated. This differential has been prepared in such a way that both the crown wheel and thebevel gear are continuously adjustable in axial direction.
....
Using electric vehicle power steering system components and front suspension system components, It can make front wheel alignment detection and adjustment, it can operate electronic control power steering system independently on the training platform according to the original car position layout.
Structure and compositions:
The Main Bench
Front suspension system and electronically controlled power steering system assembly:
Equipped with 2 independent suspension, up and down bracket and steering knuckle, hub, tire.
Booster pump drive motor (380V, 1.5KW), Steering double loading to simulate the vehicle weight and road condition device, movable frame, rotating machinery safety protection cover.
Steering booster pump, direction machine assembly, left and right horizontal tie rod, steering column and steering wheel, etc.
The Console
Speed simulation adjustment device, the main oil pressure gauge, left and right power cylinder oil pressure gauge.
Integrated with circuit fault setting module.
Equipped with ignition switch, power indicator, leakage protection switch, DC 12V switching power supply.
Made from steel sheet, zinc coated to prevent it from corrosion. The tank can accommodate up to 64 cubes 150mm side, or up to 48 cubes 200mm side. Complete with base rack and stopper for an easy water discharge. Supplied without thermostat heating system, to be ordered separately.
....
Range: 4-14 12-30
Motor: 220V/180W 220V/250W
Speed: 4800rpm 4800rpm
Wheel: CBN(HSS)or SD
Dimension: 41 x24.5x30cm 56x32x38cm
Weight: 22kg 40kg
Circuit blocks:
Resistance Temperature Detector
Thermocouple
Reference voltage supply
Current transmitter
IC transducer
Capacitive sensor
Strain gauge
Heating section
Ultrasonic transducers
Instrumentation amplifier
Infrared controller.
Theoretical topics:
Measurement of the deformation through an instrumentation amplifier
Familiarization with Infrared controllers and protocols
Measurement of temperature through a thermocouple
Measurement of temperature through an IC transducer
Familiarization with Ultrasonic sensors and transducers
Measurement of temperature through a current output IC transducer
Measurement of temperature
Fault simulation
Familiarization with capacitive sensors.
