The Torsional Vibration Equipment provides a basic range of Torsional Vibration Equipment. Steel and brass rods of two different diameters are included. A wire rod clamped in a wall mounted bracket has a heavy disc attached to the lower end. A solid ring can be located over the disc to increase its inertia. All brackets, clamps and adapters are supplied.
Torsional Vibration Equipment is part of a range designed to both demonstrate and experimentally confirm basic engineering principles. Setting up time is minimal, and all measurements are made with the simplest possible instrumentation, so that the student involvement is purely with the engineering principles being taught. Great care has been given to each item so as to provide wide experimental scope without unduly complicating or compromising the design. Each piece of apparatus is self-contained and compact.
Experimental Capabilities:
To determine the modulus of rigidity of the wire rod.
To verify the dependence of the periodic time of oscillation of a "shaft"mounted flywheel on the moment of inertia, length of shaft, and shaft diameter.
A storage case contains all the elements of the Check Valve Assembly, and the technical drawings, list of parts and instruction manual give the student all the necessary tools to assemble the valve, and the operate the valve afterwards. The Check Valve Assembly is designed for the students to become familiar with the assembly, functionality and operation of an industry standard check valve.
Experimental Capabilities:
Disassembly of check valve.
Reading and understanding technical drawings.
Assembly of industry standard check valve.
The Alternative Energy Learning System Wind and Solar includes a mobile workstation with solar PV components, small wind components, multimedia student curriculum, and teaches assessment guide. Wind turbine and solar panels also allow for outside use with expansion capability for teaching grid-tie and data acquisition. also offers alternate workstation configurations for either small wind or solar individually. The mobile workstation is equipped with pre-mounted components for easy inventory.
Alternative Energy Learning System supports the training necessary to prepare for portions of the solar and small wind certifications.The Solar And Wind Alternative Energy Training System teaches students key skills needed for job success in small wind alternative energy and solar energy. The demand for qualified solar and small wind technicians is rising, as more consumers and businesses apply solar energy and small wind systems in their communities. Many employers prefer employment candidates who are certified. Critical skill areas covered are system connection, operation, and programming of solar PV (photovoltaic) and small wind systems in commercial and residential applications. Students will receive hands-on alternative energy training and skills they can use on the job.
Convenient Indoor / Outdoor Use:
The solar array easily disconnects from the workstation and sets up outdoors. The Learning System can also be connected to client-supplied roof-top solar panels or wind turbines with the addition of optional interface connections. The Solar And Wind Alternative Energy Training System circuits can be used indoors with sun and wind simulators, or outdoors via the detachable solar panel array or client-supplied external wind and solar sources.
Features:
Convenient Indoor / Outdoor Use
Grid Interactive and Data Acquisition Options
Additional Requirements of Solar And Wind Alternative Energy Training System
Real World Components: Multiple Panel Array and Modern Communications
Solar PV Array Station:
Solar PV Sun Simulator - Alternative Energy
Electricity
Computer.
Aircraft quality electrical shielded wiring, cables, connectors, and harness assemblies are used to interconnect all units. All units are easily removable. The workstation includes two test panel consoles for bench testing of ILS receiver equipment. Instrument Landing System (ILS) Trainer is designed to provide hands-on training on a real and operational equipment approved for aircraft installation. The equipment is mounted on a mobile workstation containing aircraft ILS receiver units, NAV/VOR/GS indicator, marker indicator, marker antenna, NAV and Glide- Slope antenna.
Features:
Avionics test panels Honeywell ILS Receivers
NAV/LOC/GS Indicator
Durable,steel frame, with sturdy casters
Power Supply with voltage and current meters
Accessories storage drawers and cabinet.
Our offered bath is thoroughly checked on various parameters to ensure zero-defect. This bath is widely used in national laboratories and pharmaceutical industries. This bath is designed and developed under the strict supervision of our experienced professionals in accordance with the international quality standards.
Features:
Ideal for controlling the temperature accuracy
Durable glass bath for optimum heat preservation
Desktop based all-in-one design for easy operations and portability
Intelligent signal sampling for accurate data measuring and parameter reading
Accurate viscometer for improving experimental efficiency
Easy cleaning and drying of viscometer tubes.
High precision digital display
Electric stirrer for ensuring uniform temperature of bath.
Rockwell And Brinel Combined Hardness Tester is bench mounted unit. The principle of operation is based around a lever and weights. The weights are applied to the free end of a lever, which then transmits pressure onto the plunger, which then indents the specimen under test. Rockwell And Brinel Combined Hardness Tester is designed for measuring hardness of metals and alloys of all types (hard and soft). The specimens can be flat, or round and irregular in shape. The weights are automatically selected. A range of indenters are also supplied with 1.58 ball, 2.5mm ball and 5mm ball. Two test tables are supplied in 50mm and 38mm, with the 38mm table incorporating a Vâ„¢ groove for holding round jobs from 6 .45mm. A dial gauge monitors the loading, while a rubber bellows protects the elevating screw from dust and dirt ingress. 15 Rockwell And Brinel Combined Hardness Tester scales are available to choose from.
Experimental Capabilities:
Brinell Hardness Tests
Rockwell Hardness tests
Intended use:
Microscope slide for use with standard transmitted light microscope. For clinical laboratory use.
These specimens include blood smears, urine wet preparation, gram stains, cultures, tissue sections, etc. Used for microscopic examination of clinical specimens in haematology, microbiology, cytology, and pathology laboratories.
....
Children’s T-shirt, assorted colours, 12-14years, pack of 4.
....
Vaccine storage capacity: 61L
Volume category: >/= 60, < 120L
Refrigerant: R600a, 60 grams
Equipment operating voltage and frequency.
220-240 Volt and frequency 50Hz/60Hz, 1ph.
Operating temperature: Min and Max rated ambient temperature: +5 °C and +43°C
UIFPF- Grade A
Prequalified Intermittent Mains Powered Refrigerator for storage of vaccines at +2?C to+8?C.
Vaccine storage capacity:59L
Volume category: <60L
Solar radiation reference period of 3.5 kWh/m²/day and hot zone (+43°C) test temperatures.
Refrigerant: R600a, 45 grams
Operating temperature: Min and Max rated ambient temperature: +5°C and +43°C
UIFPF: Grade A
PQS prequalified Solar direct drive refrigerator with no battery for storage of vaccines at +2 ?C to+8?C in areas without any electricity, or where there is less than eight hours of reliable electricity over a typical day.
The 30-Day Temperature Recorder (30DTR) can be connected to a PC via an USB interface cradle (LTI-HID) and generates a 32-day report via the free Analyzer 3 software, including all relevant information per day such as min/max and average temperatures, time out of range, alarm history etc. Data can be exported from the software in CSV file format.
The device shows the actual temperature, all alarm violations over the previous 30 days (on a rolling basis), the daily minimum and maximum temperature of the last 30 days, and the time duration of any violation. With internal sensor, is an electronic 30-Day Temperature Recorder (30DTR) with factory-programmed alarms and visual display for monitoring storage conditions in vaccine refrigerators (+2°C to +8°C) over a 30-day period.
Chest type
Capacity: 383L
Cabinet Type: Chest
Volume Category: ≥ 300 <600L
Power requirement: 220-240V/50Hz and upon request 110V/60Hz
For storage of COVID vaccine at -86°C
Storage temperature: up to-86°C
Operating ambient temperature: +10 °C - +27°C (Moderate zone)
Adjustable cabinet temperature set point -40C to -86C in 1°C increment., the temperature regulation accuracy is 1°C.
Ruler, blackboard, graduated 100: 1cm and 39:1inch strong plastic, 55mm wide, 5mm thick.
Supplied in 2 x 50cm halves to be assembled and held firmly together by a detachable handle.
Set of 5 different sizes cuffs to be used with an existing blood pressure meter.
INTENDED USE
It is wrapped around the upper arm or the leg (thigh) of the patient. This is a reusable device which may be intended for single-patient or multi-patient reuse. A band-like device that has an inflatable bladder in an inelastic sleeve with one or two connecting tubes with connector (typically locking connectors) that can be connected to a mechanism for inflating and deflating the bladder and/or a sphygmomanometer or a patient monitoring device/system that is used to determine a patient's blood pressure.
Material of the simulator: Thermoplastic polyurethane - TPU (primary material for body skin), Poly vinyl chloride - PVC (primary material in chest and face skin) silicone rubber, Polyoxymethylene - POM, polypropylene - PP, and iron/steel.
Realistically sculpted to resemble and simulatea baby, anatomically accurate and feeling smooth / resilient / bony as relevant and suitable for simulation. Full term anatomically accurate newborn with umbilical cord
Texture of the simulator: soft and smooth, friction free to demonstrate the desired procedures.
Material: Polypropylene, autoclavable.
Overall height: approximately 200mm.
Internal diameter: approximately 54mm.
Depth: 180 mm.
Nasal cannula (nasal prongs), device designed for easy administration of oxygen into the patient nose through two small prongs placed in the nostrils, providing comfort for the patient.
The device consists of:
Star lumen main tube to avoid accidental blockage.
Over-the-Ear tubing adjustable
Soft funnel shaped connector to facilitate easy connection to oxygen source.
Adjustable, smoothly finished nasal tips for maximum patient comfort.
Soft twin prongs nasal tips to ensure equal oxygen flow to both.
Length of the oxygen tube: +/-2 m.
Material: Preferably soft and kink resistant polyvinyl chloride (PVC).
Single use.
Non-sterile.
Size selected: Adult
Large steam sterilizers are used for bulk sterilization processing and are typically found in the hospital's central supply department. Most operating suites and labour and delivery areas are equipped with smaller units for their own routine needs; however, areas that perform a great deal of sterilization may require large sterilizers.
Large steam sterilizer (autoclave) designed as tabletop model with a capacity of 80 litre featuring a front-loading door, suitable for bulk sterilization of wrapped, unwrapped, solid and hollow items as well as porous loads such as drapes and gowns. Electrically powered, requires a single-phase power grid supplying 230 volt, 50/60Hz, 7.4 kW.
Steam sterilization kills microbes effectively and is often viewed as the gold standard of healthcare sterilization methods. Typical items to be sterilized include surgical instrument packs, surgical implants, irrigation fluids, devices intended for and used by patients in isolation, and obstetric and dental instruments. Steam sterilizers use pressurized steam to generate moist heat to eliminate viable microbes from non-heat-sensitive medical devices, including heat-tolerant products used for surgical and general patient care.
For dissecting, clamping, grasping tissues and for passing a thread around a vein or artery.
Material: Martensitic steel (quenched, magnetic steel).
Martensitic steel composition: 0.20% carbon; 13% chromium.
Reusable.
Flexible ratchet, lockable.
Jaws which grip the thread well.
Pressure force instrument: threading forceps, springy.
Length: 23 cm.
