Analog Communication System is equipped with power supply and signal unit. Students only have to adopt the oscilloscope to complete various.
System modularity maximizes flexibility and variety for experimentation, and allows possibility for expansion and customization.
The trainer includes the basic modules with experimental circuits. It offers the beginner complete courses of basic analog and digital communication.
Introduction to sand casting: student experiments with 3 different patterns (bell, anvil and anchor).
Case for the study of foundry fundamentals.
The student will practice in first place with symmetrical pieces and after this with asymmetrical ones.
Operations of ramming up of the moulding sand, melting of the metal, pouring, forming and fettling can be performed step by step.
Training set in a case, containing:
Aluminum pattern plate.
Aluminum cope and drag box, screwable.
3 different plastic patterns:
The Anvil as a split, asymmetrical pattern demonstrates the shrinkage cavitation.
The Anchor, as a split, symmetrical pattern.
The bell as a natural or an one-piece pattern.
Rammer.
Bell clapper.
Bell mountings.
Small downgate and big downgate.
Pattern-draw tool.
Shovel.
Scraper.
Thermometer.
Soucepan.
Pencil brush.
Separating agent.
Lancet.
Brush.
The arm transmits the forceon the test model directly to a strain gauged load cell. The load cell is connected to a readout unit with a digital display, which is powered by adesktop power supply (included). A two-component balance which measures the lift and dragforces on models mounted in Subsonic Wind Tunnel. In addition, the equipment is fully compatiblewith Versatile Data Acquisition System and can quickly and conveniently connectto the frame mounting interface unit. The balance mechanism enablestest models with a rigid support arm to be mounted and held securely inposition in the working section of the wind tunnel. When mounted in the base of the wind tunnel working section, the balancemeasures the drag force only. This is useful for a variety of investigationssuch as wind loadings on tall buildings. To measure the lift and drag forces onmodels the balance mounts on the side of the working section of the windtunnel. The drag force is measured first, and then students rotate the balancemechanism through 90 degrees and repeat the test to measure the lift force. It can also be used to measure dragforces on model vehicles enabling students to determine and comparecoefficients of drag.
....
To determine metacentric height of floating body and height variation with tilt angle. Tilt angle indicated by plumb bob on attached scale. Rectangular pontoon; centre of gravity can be moved side way by moving horizontal jockey weight, and vertically via adjustable vertical weight on mast.
....
Blood sample separation for clinical laboratory tests (serum, plasma, etc).
....
Basic Electrical and Electronic Appliances EX Board B
....
This set is sufficient for most examinations of complex wounds, appendectomy according to Mac Burney, non-complicated ruptures, etc. It is the best basic emergency surgical box.
This set should be considered part of any minimal investment in a health facility with surgical activities. A fully functional environment with theatre, sterilisation and resuscitation rooms, as well as trained personnel must be available.
Components:
DC Power Switch with indicator light
Master Power Switch with indicator light
Solder-tail aircraft connector
Audio alarm
Circuit Breakers
DC power buss
Relays
Switches
Terminal strips
Voltmeter
Ammeter
Indicator lamps
Power Requirement: 110V AC or 220V AC
Dimensions: 18 L x 18 W x 10 H inches.
The EFIS used in is a versatile unit that includes several features representing a modern EFIS display. The Basic EFIS Trainer provides an introduction to a general aviation Electronic Flight Instruments System (EFIS).
EFIS Features:
External GPS Receiver with database
Autopilot Interface
GPS Interface
ILS Interface
NAV Interface
External Remote Compass System
Interface
H.S.I Resolver Interface
Emergency Power Battery
Altitude Encoder Interface
An ECG monitor included with the unit is used to verify the presence of a shockable rhythm and the effectiveness of treatment. Defibrillators deliver a high-voltage electrical impulse to the heart in order to restore normal rhythm and contractile function in patients who are experiencing ventricular fibrillation (VF), ventricular tachycardia (VT), or another shockable rhythm.
....
Basic Installation Training Package Unit may be thermally loaded for performance investigation and has a dial thermometer, Internally equalised Thermostatic Expansion Valve; High Pressure Switch; Low Pressure Switch; Liquid Line Filter Drier; Liquid-vapour Heat Exchanger; High Pressure gauge; Low pressure Compound gauge.
Basic Installation Training Package Unit consists of an air cooled condensing unit with high back pressure, high starting torque hermetic compressor, Complete with: Suction and Discharge Service Valves; Gauge Manifold Connections and Built in Motor Protector.
The evaporator is a finned coil type with fins a 5 fins per inch. Basic Installation Training Package Unit powder coated evaporator is a forced air, blow through type with removable front panel and galvanised sheet steel casing.
A warming unit using a heated mattress and a nest type frame to raise or maintain a newborns’ or premature babies body temperature through conductive heating. A liquid bases warmer system to assist premature babies maintaining the appropriate body temperature.
....
An infant incubator provides a closed, controlled environment that warms an infant by circulating heated air over the skin. Incubators feature better temperature control than radiant warmers (overhead heating units), which can overheat or underheat the infant. However, an infant in an incubator is less accessible to the caregiver. The heat is then absorbed into the body by tissue conduction and blood convection. Ideally, both the skin and core temperatures should be maintained with only minor variations.
....
The apparatus consists of two rafter struts and a restraining tie mounted on a self contained, bench top base.
Evaluation of co-planar forces in the struts and tie of a basic roof truss
Effect of changing tie bar length
Loading at the hinged apex by load hanger
The tie length, and hence angle of truss, variable
Both struts and tie incorporate linear, direct reading spring balances to measure forces
An instruction manual for student and lecturer provided
Struts and tie re-adjustable to original lengths
Set of weights.
Used for microscopic examination of clinical specimens in haematology, microbiology, cytology, and pathology laboratories.
These specimens include blood smears, urine wet preparation, gram stains, cultures, tissue sections, etc.
These specimens include blood smears, urine wet preparation, gram stains, cultures, tissue sections, etc. Used for microscopic examination of clinical specimens in haematology, microbiology, cytology, and pathology laboratories.
....
Material of the simulator: Thermoplastic polyurethane - TPU (primary material for body skin), Poly vinyl chloride - PVC (primary material in chest and face skin) silicone rubber, Polyoxymethylene - POM, polypropylene - PP, and iron/steel.
Realistically sculpted to resemble and simulatea baby, anatomically accurate and feeling smooth / resilient / bony as relevant and suitable for simulation. Full term anatomically accurate newborn with umbilical cord
Texture of the simulator: soft and smooth, friction free to demonstrate the desired procedures.
mm/inch
Throat clearance: 380/15
Spindle vertical movement: 25/1
Work table size: 355x355/14x14
Up/down movement of table: 125/5
Routing work table size: 610x420/24x161/2
Table tilt degree: 15
Spindle speed (rpm): 11000
Power required hp/rpm: 1.5/2800
Material of the simulator: Thermoplastic polyurethane - TPU (primary material for body skin), Polyvinylchloride - PVC (primary material in chest and face skin) silicone rubber, Polyoxymethylene - POM, polypropylene - PP, and iron/steel.
Full term anatomically accurate newborn with umbilical cord.
Texture of the simulator: soft and smooth, friction free to demonstrate the desired procedures. Realistically sculpted to resemble and simulatea baby, anatomically accurate and feeling smooth / resilient / bony as relevant and suitable for simulation.
