The instrument is mainly used to measure the height of sun. it consists of protractor,angle indicator,hanging wire hammer ,base and screws.
....
Measurement of amperage and voltage to determine the power at the evaporator
Investigation of a vapour jet compressor
Vapour circuit with pump and vapour generator for operating the vapour jet compressor
Vapour generator with electrically heated water jacket
Transparent tank with water-cooled pipe coil as condenser
Flooded evaporator with float valve as expansion element
Transparent tank with adjustable heater as evaporator
Refrigeration circuit with condenser, evaporator and vapour jet compressor for refrigerant.
Compression machine 1300 KN hand operated 1 gauge to test cylinders up to dia. 160x320 mm and cubes up to 150 mm side.
....
Pressure vessel with valve for draining
Display at switch cabinet to indicate active power
Test unit for a small industrial compressor
1-cylinder compressor
Water jet pump to evacuate the tank
Sensors for temperature, pressure and flow rate with digital display
Visualisation of the condensation process of water in a transparent tank
Pressure switch and safety valve for safe operation
Controlled heater to adjust the boiling temperature
Two water-cooled tubes as condensers with different surfaces to realise film condensation and dropwise condensation.
Laboratory-sized steam power plant
Synchronous generator with ppu synchronising device for grid connected or stand alone operation
Gas/oil-fired once-through steam boiler with electrical superheater
Single-stage industrial steam turbine with curtis wheel
Electronic speed control with electro-pneumatic control valve
Modern digital system control via a process control system
Control station with complete instrumentation on modern LCD monitors, touch screen operation
Water-cooled condenser with cooling water circuit and wet cooling tower
Feedwater treatment with ion exchanger and chemical dosing.
9 potentiometers for the setting of
Relative humidity: 0...100%
Coolant flow rate: 0...100kg/h at 15°c
Intake pressure: 0...2bar abs.
Intake temperature: 0...100°c
Flow control valve setting: 0...100%
Vessel, nominal pressure: 0...50bar
Dead space: 0...100%
Motor speed: 0...1000min-1
Vessel capacity: 0...1000l
Inputs and outputs
4x digital in/out
16x analogue in, 1x analogue out.
Straight and inclined loading possible.
Strain gauge to measure force on each bar.
Investigation of bar forces in statically over determinate trusses.
Surplus bar, longitudinally adjustable.
Measurement amplifier required.
Storage system to house the components.
Experimental set-up in frame.
Software to evaluate measurement data.
Measuring a vapour pressure curve for saturated vapour
Bourdon tube pressure gauge to indicate pressure
Digital temperature display
Boiler with insulating jacket
Temperature limiter and safety valve protect against overpressure in the system.
Influence of dead-weight minimised by horizontal experiment layout.
Investigation of bar forces in a single plane, statically determinate truss.
Ready assembled Warren truss beam.
Pre-balanced strain gauge connection box.
Supplementary set for the main unit.
Any straight and inclined load cases possible.
Products are stainless steel products;
Four pieces for one set, including anatomical scissors, forceps, scalpel, anatomical needle each;
The tweezers are of moderate elasticity, close to the forceps arm, and the ends of the tweezers are closed, with no slits or micro slits;
Anatomical scissors tip, two blade cross anastomosis, flat;
There is no gap, the blade edge cracks, smooth straight needle.
The guards are both on front, back and lateral side and are easily/quickly fixed to the machine with hooks. Fragment guards to Safety Directive, manufactured from highly resistant transparent polycarbonate material. Machines 3000kN and high stability 3000kN.
....-lab-556267877.jpg "Dissector (Seven Parts)")
Products are stainless steel products;
Seven pieces for one set, including anatomical scissors,shearing scissors, tweezers, forceps, curved straight round bladed scalpel, straight bladed scalpel, the anatomy of a needle each ;
The tweezers are of moderate elasticity, close to the forceps arm, and the ends of the tweezers are closed, with no slits or micro slits;
Anatomical scissors tip, two blade cross anastomosis, flat;
There is no gap, the blade edge cracks, smooth straight needle.
Investigation of bar forces in statically over determinate trusses
Strain gauge to measure force on each bar
Measurement amplifier required
Surplus bar, longitudinally adjustable
Straight and inclined loading possible
Software to evaluate measurement data
Experimental set-up in frame.
Storage system to house the components.
The DEM is a three-phase asynchronous squirrel-cage motor mock-up that can be assembled and disassembled depending on needs.
This Dem Dissectable Machine is presented in a case containing the following items:
The motor housing with stator wiring, fitted with a terminal block
The fan
The left and right flanges
The squirrel-cage rotor
The screws with screwdriver kit.
Heating circuit with heater, pump and expansion vessel
Visualisation of evaporation in a tube evaporator
Cooling circuit with water jet pump to generate negative pressure (vacuum)
Heating and cooling medium: water
Safety valve protects against overpressure in the system
Tube evaporator made of double-wall glass.
Digital display for air flow rate, temperatures, pressures, differential pressures and compressor speed
Intake vessel with measuring nozzle for determination of the suction volume flow
Intake vessel and pressure vessel, both with pressure sensor and additional manometer
Single-stage piston compressor with one cylinder
Drive and speed adjustment via
Blow-off valve with silencer for setting a steady flow operating mode
Safety valve and pressure switch with solenoid valve for limiting the pressure.
Upper And Lower Compression Platens complete with ball seating, dimensions 510x320x55 mm for tests on blocks.
....
Upper Compression Platen With Spherical Seat, to obtain an increased vertical clearance of the testing chamber, to fix on the testing machine.
....
Coveralls feature a polypropylene breathable SMS fabric with a cloth-like feel.
The Reflex Coverall Design is 7.5 times more rip-resistant than ANSI minimum standards and offers excellent fit and freedom of movement for the wearer.
This personal protective apparel is triple-bagged and vacuum packaged, suitable for ISO Class 5 or higher cleanrooms.
Clean Processed Cleanroom Coveralls/Case
Triple bagged, vacuum packed, suitable for cleanrooms
Reflex Coverall Design offers excellent fit and freedom of movement and 7.5 times more rip-resistant than ANSI minimums
Clean Processed Cleanroom Coveralls have an average bacterial filtration efficiency (BFE) of 96% and are made of 100% polypropylene breathable SMS fabric, which gives the wearer cloth-like comfort.
It is made without latex, silicone and the BHT preservative and is designed for single-use (disposable PPE). The easy-to-don, individually packaged coveralls feature a mandarin collar, thumb loops and tunneled elastics.
Clean-processes and individually packaged under cleanroom conditions
This protective apparel isn't made with natural rubber latex, BHT preservative or silicone
Greener Choice Claims
Environmental benefits include:
Recyclable.
