It is mainly used for the experiment of red, green and blue color synthesis.
....
Single layer, spun bond polypropylene
Latex-free
Lightweight spun bound material provides disposable protection against dirt and grime.
White
Lightweight, breathable fabric keep workers cool and comfortable.
Elastic wrists without pocket
Snap front
White.
These enable individual line sections to be checked-eachswitch, each pin on the control unit, each output component and each bussection. Training stand networked systems, with optional e-learning companion course. It is immediately ready for use and offers 41 practicalerrors. The optional addition for the driver's door expands the system by afurther 12 faults as well as their breakout box and pin outs. The unique teaching device is characterized by the continuous use of bridge plugs with measuring tap. Thus, the device is ideal for diagnostic training in the field ofcentral electrics.
Features:
Frame made of aluminum profile with casters, with tabletop
All components are wired inside the unit, thus the system is ready for useimmediately
Fully functional CAN-lighting wall, original components VW Golf 6, specially preparedfor training purposes
Diagnosis:Each control unit can be individually suspended and measured, and each busconnection at both ends
Integratedregulated power supply 12 volt
Frontpanel prepared, color printed
Numerous test sockets for all components of the central electrics, numerous test socketsfor all bus connections.
Industrial type components are educationally adapted byusing a modular panel system to permit the step by step assembling from thesimplest circuit to the most complex system. This laboratory is designed for the study of the lightingplants and to allow the student a practical training, based on the performanceof guided experiments. The configuration allows theperforming of the following exercises:
Double Pushbutton
Brightness Control
Dimmer
IT TX/RX.
The training device is based on the Jetta lighting system. And it can fully display the structure and working process of the automotive lighting system.
Structure and composition:
Headlights, front corner lamp, front fog lights, dimmer switch assembly, tail lights, license plate light, rear fog lamps, side lights, lighting switch assembly, brake light switch, reversing light switch, high-capacity battery or 12V switch power, terminal detection, fault set and troubleshooting system, mobile bench.
Features:
The working principle and process of the lighting system can be demonstrated.
It has troubleshooting and set areas. You can set multiple common faults, stimulate the fault, test the fault and exclude the fault.
It is based on the automotive lighting system components. And it can display the structure of the lighting system.
The color schematics is very easy for the students to analyses and understands the work process of the automotive lighting system.
Training board-simulator is a great educational tool that allows students to learn the structure of lighting system, study its components, and perform various measurements, tests and other diagnostic procedures. Fully functional Lighting Training System installed in a mobile aluminium frame and it is based on OEM components of VW/AUDI cars.
The main characteristics and functions of the Lighting Training System trainer are:
Adjustable level with the motors of front headlights.
Possible adjustments training with the headlight tester
Open contacts for measuring of system's components and circuits.
Electric wiring diagram with built-in banana plug jumpers for measurements and connecting or disconnecting the components
The Lighting Training System has the following diagnostic and measurement features:
Electronic control unit (ECU) identification
Displaying the operating system parameters (live data)
Control unit diagnosis
Throttle adaptation
Reading/erasing fault codes
Diagnosis through OBD 16 pin diagnostic connector
Activating the actuators (depending on the control unit).
Ideal for general inspection work, or for use as liners underneath unlined liquid proof gloves.
Wear alone for inspection purposes
100% cotton lisle gloves
Two-piece construction
Ambidextrous.
Can be used as liners under liquid proof gloves.
Premium quality, cotton lisle inspection gloves
Designed to minimize contamination of products, with an extended cuff for additional protection.
100% cotton fabric
Two-piece, reversible pattern
Effective as liners under disposable and unsupported liquid-proof gloves
Unhemmed.
Possible demonstrations:
Function ofthe thrust rings
Function ofthe friction plates
Locking
Differentspeeds of axle shafts when cornering.
Proprietary polypropylene laminate fabric provides effective contamination control and protection from liquid-splash and dry-particulate cleanroom hazards.
Maximum containment short of a full coverage coverall. Limited-use, full-length frocks offer the breathability and comfort of microporous film fabric.
Serged seams
Elastic wrist
White knee-length frocks
Microporous film fabric
Bound neck
Antistatic treated.
Available with a five-snap or zipper front closure.
Combines strength with the softness and comfort of linen
Pants
Have a latex-free elastic waist and one back right pocket.
Scale factor: 1:1000
Three-phase model of an overhead power transmission line 360 km long, voltage 380 kV and current 1000 A.
It is used for student grouping experiment in middle school physics and mainly consists of resistance wire, graduated scale, sliding key and stent.
....
Inner packs dimension (L*W*H CM): 35.5*24*36
....
The heating section, cooling section and one of the intermediate sections are fitted with thermocouples (eight in total) evenly spread along the length of the assembled conduction path.
A small-scale accessory designed to introduce students to the principles of linear heat conduction, and to enable the thermal conductivity of various solid conductors and insulators to be measured.
Includes a water pressure regulator, an electronic proportioning solenoid valve to control the cooling water flow rate and a water flow meter.
Comprises a heating section, cooling section plus four intermediate section conductor samples and two insulator samples.
All sections are insulated to minimize errors due to heat loss.
Includes a water pressure regulator and a manual flow control valve.
Heater power variable up to 60 Watts.
Water flow rate variable up to 1.5l/min.
Heating and cooling sections, 25mm diameter.
A comprehensive instruction manual is supplied.
The accessory is mounted on a PVC baseplate, which is designed to stand on the bench top and connect to the Heat Transfer Service Unit without the need for tools.
The cold section is of identical dimensions to the hot end and is water-cooled. Both the heated and cooled ends are each fitted with three thermo couples at 15mm intervals to measure the temperature gradients along the bars.
A small-scale accessory that allows experimental investigation of linear heat conduction and the measurement of the thermal conductivity of various solid conductors and insulators.
The hot end uses a nominal 65W heater (operating at 240v maximum), which is fitted with a high temperature limit switch. The power supplied to the heater is controlled and measured by the Heat Transfer Service Unit .
An insulated, 25mm diameter brass heated section and cooling section that may be either clamped together, or assembled with one of four insulated intermediate sections or test specimens between the interfaces.
Bench top for investigations on motion, plastic and elastic impact, momentum, spring-mass oscillation and on friction System to consist of:
Inclinable track with stoppers at both sides
Friction block
Plunger carriage
Device for actuation of carriages and friction block
3 tension springs
Rolling carriage
3 sets of weights
Deflection pulley
Cord
Moveable stopper for track
3 buffers with rubber buffer heads for covering of permanent magnets
Additional weights for carriages including measuring tape: length: 2000mm, resolution: 1mm.
