Ideal for training in the operation, maintenance, repair and troubleshooting.
Main Features:
Piston compressor
Condenser
Dehydrating filter
Max. power 2 kW
Cooling liquid 400gt
Troubleshooting device for simulation of 4 faults
Nomenclature table
Pressure switch
Resistor
Thermostat
Expansion valve
Evaporation unit.
The experimental set-up enables fundamental experimentation in the mechanics of deformation. Flat rods can be permanently deformed by means of a simple bending device. A suitable force measuring device and a wide range of specimens are supplied. The well-structured instructional material sets out the fundamentals and provides a step-by-step guide through the experiments. A range of different materials and bend radii can be investigated using this experiment. The experiments should be conducted in a workshop environment, as the bending device has to be clamped into a vice. The necessary deformation work, e.g. to produce a 90° angle, is recorded in the experiment using a force measurement system.
....
The Set Of Sectioned Components For Thermic Plants includes some of the most important components, used in thermic plants. Special explanatory technical plates show each sectioned component explaining its operation with notes, drawings and technical data. The use of contrasting colours according to a pre-established code simplifies the informative process as well as the learning one. In sectionizing each component the best care has been taken to evidence all the interesting constructive detailed features.
....
Single Effect Falling Film Evaporation Pilot Plant With Software
....
Compact laboratory designed for training of 14 years students and over. The Air Conditioning Mobile Lab is already equipped with all the necessary feed fittings according to the industrial standards. It is ideal for all teaching environments and its modular design guarantees both flexibility and adaptability for all the experiments. It is particularly suitable to introduce the main and practical air conditioning applications in both vocational and technical schools. The trolley is completely mobile and has 5 storage drawers, protecting the equipment in shock-free, molded sponge pods. It is possible to compose the circuit on the aluminum surface to place on the working top. Opportunity of fault insertion and detection. You can organize the equipment according to the subjects for quick and easy setup and control of the equipment itself.
....
Set-up of a equal-axled three-shaft transmission
Shifting the 6 forward gears and the reverse gear
Reading and calculation on the various ratios
Pushing together and separation of the shafts
Insertion of the reverse pinion.
It can carry out multi-type experiment and it is suitable for electronic technology research and development in the vocational and technical school and universities. Logic Circuit Training Kit is a comprehensive electronic design platform for electronic system designed teaching.
....
Cylinder mould dia.160x320 mm.
Weight 2560 g
Features:
For shearing & bending, both can achieve single strokeand continuous stroke.
The back gauge adopt data control system, the adjustment isquickly and exactly.
Ideal Combination of Shearing, Brake & Rolling with Strong Structure.
For the Rolling, the processing for the taper rolling is very easy.
For this reason it is an effective, safe and innocuous therapy for the treatment of all the muscle and skeleton pains, neuralgias, rheumatic pains, articular pains, headaches, lumbar pains, sciatic pains and other affections. T.E.N.S., or Trans cutaneous Electrical Nerves Stimulation, is a particular low frequency wave form that, once applied through electrodes in the area of the cutaneous projection of the pain (triggers area), allows an almost immediate and long lasting reduction of the painful sensibility.
Circuit blocks of Trans cutaneous Electrical Nerves Stimulation
Typical circuit that is used in the T.E.N.S.
Mechanism through which electrical pulses are able to perform an analgesic effect
Designed as a teaching system, this learning system showcases components, often not visible in actual installations, on a vertical panel that permits easy access for hands-on skills and observation. Geothermal Energy Training System builds knowledge as well as skills across a broad spectrum, ranging from system startup and operation to shut down and maintenance, in a readily accessible, compact vertical trainer. Geothermal Energy Training System enables learners to understand and apply their newly obtained technician skills in the ever-growing area of geothermal energy. Harnessing geothermal energy is rapidly increasing in importance as a tool in broadening the energy supply. Geothermal Learning System packs a residential-sized system into a 6-ft.long mobile system that easily fits through a standard door. Major components include a 2-stage compressor with a 2-ton heat pump, ground simulator, air duct with blower, ground source loop, and industrial grade geothermal controller. These components and many more come standard. Includes a ground simulator so that learners gain realistic experience using a continuously operational system like they will experience on an installed system.
Features:
Ground Simulator Allows Continuous Training
Industry Standard System Components and Features
Integrated Multimedia Curriculum.
The possibility of further integrations or updating in the future is obviously ensured. The Transducers And Automation Modular Laboratory is an extremely flexible and efficient modular training system for the study of industrial transducers and relevant electronic circuits of signal conditioning and conversion. By means of its modular composition, it is possible to choose the optimal configuration according to any specific educational requirements and available budget. A Personal Computer Data Acquisition System is also available in order to allow the computerized measurements to determine the transducer characteristics.
....
Measurement of oxygen concentration, temperature and flow rate
2 hand-held measuring units for measuring the oxygen concentration upstream and downstream of the absorption column
Falling film column for the absorption of oxygen from the ambient air in a solvent (water)
Counter flow process
Continuous regeneration of the solvent with nitrogen in a desorption column by stripping
Pump for recirculating the solvent to the absorption column
1 compressor for supplying ambient air into the falling film column
Pump for desorption column.
Hooks Joint Mechanism
....
The deflection of the bar as result of the travel of the dynamometers and the horizontal alignment can be compensated and regulated using two adjustment bolts. This demonstration unit facilitates the experimental investigation of the progression of the bending moment and shearing forces on a bar subject to point loads. Due to the use of a low friction joint with two degrees of freedom at 1/3 of the span and two dynamometers, the measurements can be recorded directly from the bar. The bar is loaded with graduated sets of weights that can be attached at any point on the bar. In addition, the section principle commonly used in mechanics can be demonstrated.
....
The main part of the apparatus is a precision-engineered rigid aluminium base, with legs and levelling feet. At one end is a loading device which uses a screw to apply loads to the struts. The screw is in fixing blocks with bearings to give precise and easy load application. The Loading and Buckling of Struts allows tests on a full range of struts. They allow students to create any combination of pinned or clamped end conditions for the strut under test. Supplied is a set of special end fittings for tests with various eccentricities to show the effect of eccentric loading. It shows load and deflection characteristics and buckling loads for various strut lengths, Cross-section and end conditions. It also allows studies of the effect of eccentric loading. The equipment includes a lateral pull attachment for Students to apply light biasing loads, or larger side loads, as needed. Students can also set up the apparatus to examine flexural rigidity and general beam deflection theory. An optional set of extra specimens allows extra tests to show students some of the more complicated problems found in strut design. Holders are at both the loading and load measuring ends.
The two special struts show how buckling loads may be lower than the ideal values, because of two reasons:
Imperfect shearing connections between the parts of a compound strut
Flexure of the end fixings.
The angular position of the cam is shown on a protractor and a pointer, this assembly allows the cams position through rotation to be recorded. A vertical pillar contains the main spindle for each Cam Analysis Apparatus to be rotated, whilst a dial gauge has its anvil resting on the top edge of the cam. The rise and fall displacement of the Cam Analysis Apparatus, as it rotates through 360°, is measured using a dial gauge. Cams and followers are easily changed and graphs for the variety of cams can be created to compare the linear change with the rise and fall of the follower. Each cam is mounted on a central shaft and is free to rotate about this shaft. The cams are rotated by hand.
Experimental Capabilities:
To derive the velocity and acceleration diagrams, and determine the maximum acceleration of the follower
To compare experimental and calculated results
To determine a graph of follower displacement against angular rotation of the cam
To assess the effect of different cams and followers.
The industrial digital multi-controller will monitor and react to adjust parameters to achieve set-points with variation of outdoor air temperature, room temperature and relative humidity, thermal factor, incoming air temperature, incoming air flow and refrigerant flow.
A Domestic Building Air Conditioning Control Simulator for studying the management of automatically controlled air conditioning systems installed in residential buildings.
It also includes a configurable, industrial digital multi-controller that automatically monitors and controls different parameters to ensure the set-points are maintained.
The has been designed and manufactured to incorporate all current safety standards.
The simulates ON/OFF digital control and proportional analogue control. However, simulated PID control can be included upon request.
This experimental and demonstration apparatus consists of an open channel of rectangular cross section supported at each end by frames, one of which is adjustable so that the slope of the channel may be varied. This Flow Channel provides a low cost experiment with accuracy comparable with larger scale channel investigations. The channel walls are made from clear acrylic plastic so that full visibility of the flow characteristics can be achieved. A number of test models are provided along with inclinometer and surface profile measuring instrument.
Experimental Capability:
Hydraulic jump - determination of energy head and power loss at the jump section by means of specific energy considerations.
Study of long base weir and calibration of broad crested weir.
Study of Venturi Flume, observation of flow through a throated Flume, calibration of the Flume when used as a flow measuring instrument.
Study of uniform flow in inclined channel, verification of Chazy equation and determination of Chazy Coefficient and Mannings Friction Factor.
Calibration of sharp crested, thin plate overshot weirs. Friction factor and roughened channel bed studies.
Determination of Hydraulic Mean Depth for the flow channel.
Study of flow over triangular hump section, plotting of Specific energy - Depth relationships, comparison of theoretical and experimental values of critical height.
Study of flow under a sluice gate (undershot weir) with application of Specific Energy and Momentum Functions.
Suspension Steering And Brake Program has the complete strut assembly. tires and wheels. and fully functional hydraulic power steering with complete front disc brake system. Suspension Steering And Brake Program is based on task list and provides the student with a trainer which can simulate various road conditions. The program is completely operational with power steering, tires and front disc brakes. Strut mounting points, which replicate Chrysler factor/ specs. allow alignment/adjustment for aster and camber. The readily accessible components make the instructor's task relatively easier. The Strut Suspension can be loaded with hydraulic double acting pistons that are mounted to allow load to be created under the control arms letting tires spin freely and brakes to function properly. The component operation. identification and diagnosis of problems an be pinpointed and replaced/repaired by the student.
....
