The Hydrostatic Pressure On Submerged Surfaces system is designed to study and calculate of the pressure force acting on a submerged surface Hydrostatic Pressure On Submerged Surfaces is a simple and completely autonomous equipment that can be easily located in a laboratory without any installation.
It is possible to use liquids of different densities to determine the different exerted forces between them.
With this equipment it is possible to perform the following experiments:
Obtaining and verifying the momentum created by pressure force acting on a submerged curved surface.
Measure and verify the momentum created by the pressing force acting on a submerged flat vertical surface. For that it is necessary to determine both the magnitude of the force and its pressure center. It is possible to distinguish two different cases:
Partially submerged surface.
Complete submerged surface.
The unit consists of three type of sensors with four indicators, and five different other temperature measuring devices. Temperature Measuring Bench top unit is used for studying temperature measurement of several commonly used devices as well as understanding related principles. Heat sources and means for calibration and accuracy comparison of the different devices is also provided.
Experiments:
Understanding lead and conduction errors.
Dynamic response.
Understanding the physical principles of each device.
Understanding calibration techniques.
Air humidity.
Errors associated with incorrect applications.
Thi smechanical supercharger is installed in Daimler Benz compressor sports cars. The suction and compression can be shown particularly clearly. The two rotors have three vanes each and are driven via gear wheels.
....
The teaching board contains whole car electrical system. It can fully show the structure and working process of the car electrical system.
Structure and composition:
starting system, charging system, wiper system, lighting system, terminals and connections, wiring diagrams instructions, failure settings and troubleshooting system, mobile gantry, electric windows, instrumentation systems, sound systems, high-capacity battery or 12V switch power, etc.
Features:
It can fully demonstrate the structure of the various systems and the working principle of the car electrical system.
Diagnostic block is installed on the panel which can be connected to an auto decoder. And you can use an engine self-diagnostic functions to read the fault codes from the engine electronic control system, and clear the fault code and reading data stream.
It allows the students to conduct series training of the whole car electrical system.
It has the troubleshooting and faults setting system. You can set multiple faults, stimulate the fault, test the fault and solve the fault.
Two channels computerised graphic display system to control and manage all sorts of semi-automatic testing machines, processing, printing and saving the test data and certificates, for acquisition, display, with software for remote control from PC.
....
It is suitable for accurate and diverse jobs. They are tough, stable and dependable. Their user friendly features and higher cutting capacity leads to higher efficiency. These devices are made using high quality components to meet extreme load conditions. They are simple to maintain and have longer working life. All Geared Universal Milling Machine is used to precisely shape metal and other solid materials. We offer manually operated, mechanically automated and digitally automated CNC milling tools. This device comes in 4 different specifications or formats as shown in the below table. There are milling tools with smaller as well as larger work surfaces and therefore can be selected depending on the most specific requirements. Our heavy duty, versatile tools are built for hassle-free operations. It has been designed for faster work and comes with a rotating spindle which can rotate at the speed of 40 to 1200 RPM ensuring really quick and efficient work in the industries. Our tools are applicable in machine shops and tool rooms of many industries. Our universal tool supports longitudinal, vertical as well as cross feeds. The instrument is designed for optimum performance and is just the right device for robust and bulk industrial applications. Fabricated from high quality raw materials, this is a long lasting instrument which ensures to give a comparatively greater and hassle-free functional life than other ordinary machineries available in the market.
Features:
Steel Sliding gears carried on Splined shafts, Spindle and Arbor made of alloy steel hardened and ground.
High Quality Close grained Cast Iron All Slides Grinded on Slide way Grinder and closely scraped.
The Power Electronics Board allows the study of several power electronics circuits, as detailed here under.
Technical Features:
The following components are available of Power Electronics Board:
Pulse generator for SCR control
Generator for H Bridge control
Diodes for circuit
Three-phase generator
Single-phase source Built-in power supply
SCR for circuit
H bridge with MOSFET
Function Generator.
The automatic control is performed through a PLC, whose program manages the displays signaling vacant and full places for both zones and the opening and closing of the in and out barriers. Two Zone Parking Garage Simulator represents a two-zone parking garage where it is possible to realistically simulate the sequences that a car driver has to perform when he wants to use an automated parking garage. The number of cars in the parking garage is displayed through LED.
....
Hydraulic cylinder with hydraulic pump to generate pressure
Hermetically sealed hydraulic system, maintenance-free
Investigation of the stresses and strains in a thin-walled cylinder under internal pressure
Strain gauge application on cylinder surface at various angles
Cylinder usable as open pipe or as closed tank
Gauze compress, surgical folding, i.e. so that there are no free threads apparent after folding or when the first outside fold is opened. Non-detectable by X-ray.
Thread count warp 95 to 105 threads/dm;
Material: Absorbent gauze, 100% cotton.
Sterile.
Disposable.
Type of gauze: 17 threads/cm2 (grammage 23g/m2).
Components: Bleached, purified textile, plain weave.
Number of folds (thickness): 12.
Initial sterilisation method: Ethylene oxide gas or ionising radiation.
Size selected: Compress, gauze, folded.
Width: approximately 10cm.
Length: approximately 10cm
Weft 66 to 74 threads/dm
Weight: Approximately 23g/m2.
The product is mainly composed of three sets of 50mm diameter single pulley and the table clamp,three iron rings,three nylon line. Pulley angle can be adjusted.
....
The maximum circular arc diameter of the vessel is 55mm; the protective cover is provided with an anti shock pad block. It consists of container, sand, a set of protection, etc.
....
It is used to set up Cesium chloride crystal structure model.
....
The structure of the socks allows high wear-resistance and durability while maintaining good elasticity.
Abrasion-resistant, soft, and comfortable to wear.
The product should be stored in a ventilated, dry, mildew-proof and insect-proof place.
Avoid prolonged product exposure to sunlight.
Do not rub against rough objects directly.
Launder using a neutral or slightly alkaline (pH <9) synthetic detergent on a gentle cycle to prevent mechanical and chemical damage
Disposable Cleanroom Socks are a cost-effective and cleanroom compatible option for cleanroom and extended wear.
Laundered and packaged in Class 5 Cleanrooms, with extremely low particulate contamination
If the socks are torn or the yarn begins to falls off or tear in multiple places, replace them.
Force Sensor High Resolution
....
An exploded-view of the jig is printed on the cover to illustrate the construction of the jig. A quarter segment has been cut out of the main body of the drilling jig. The basis for the course is a drilling jig which can be used to drill holes in a bearing cover. All drilling jig components are clearly laid out on a base plate. The cut-away quarter segment is also present on the base plate, enabling the difficult topic of sectional views to be illustrated. All parts are precision-manufactured on cnc machines and are therefore also suitable for measurement exercises. It can facilitate the drilling of the workpiece and other small parts. This enables demonstration of the terms 'section' and 'half section' as used in technical drawing. The comprehensive instructional material is laid-out in line with modern principles and provides effective assistance with lesson preparation. Optimal learning is established when groups of two or three students work on one model.
....
The channel is totally transparent so it allows an optimum visualization of the hydraulic flow. The purpose is to study the flow behavior in open channels and closed pipes, by realizing some experiments in both conditions. These points are connected to the 6 tubes manometer. By floodgates, it is possible to increase water volume in the inlet or outlet tanks. In order to carry out experiments in a closed chamber, the module includes a cover for hermetically seal. Pitot tubes are arranged along the whole length of channel, so it allows measuring the working pressure in 6 points. The equipment can be used stand alone or in conjunction
Open channel:
1. Study of water flows through open channels identifying variables like:
Speed at different points of the cross-sectional area.
Water height
2. Study of constant water flow, gradually varied flow and behavior of surface profiles.
3. Study and utilization of thin edged weir for flow measurements.
Rectangular weir without lateral contraction.
4. Study and utilization of broad crested weir for flow measurements.
Rectangular weir.
5. Analysis and study of discharge under a gate.
Vertical weir
6. Study of jump spillway
Temperatures and pressures at various points are indicated. Sight glasses are provided to indicate the state of the refrigerant. Basic Refrigeration System is used for demonstration of a normal household refrigerator operation. Individual components are clearly shown.
Experiments:
Observation of pressures and temperatures.
Using a p-h state diagram.
Study of layout and process diagram.
Made from extremely robust and stable polyethylene, complete with base rack. Curing tank 650 liters capacity, heavy plastic. Supplied without thermostat heating system to be ordered separately.
....
